Table of Contents
Advertisement
50
EN
1
2
N U M BER
1
M EN U
2
Storing Cha nnels M a nua lly
Store channels that were not stored during Auto Set Up (
Preset Download (
ACCESS MAIN MEN U
Press M EN U .
1
ACCESS CO N FIRMATIO N
SCREEN
Press %fi to move the highlight bar (pointer) to
2
" MANUAL CH SET" , then press O K or
mation screen appears.
SELECT PO SITIO N
Press % fi
3
@ #
open position in which
you want to store a
channel begins blinking,
then press O K . The
Manual Channel Set
screen appears.
Downloaded from:
https://www.usersmanualguide.com/
– –:– –
1
2
3
4
5
6
7
8
9
3
0
4
4
3
pg. 6) or Auto Channel Set (
. The Confir-
#
(Ex.) To store in position 12.
until an
PR
CH
ID
01
25 ARD
02 CDB SKY1
03
10
ZDF
04 C65 RAI1
05 C31 BBC1
06 C32 BBC2
07 C33 3SAT
[ 5 ∞
]
: EDIT
=
= [X] : DELETE
[MENU] : EXIT
The blueback screen and the
programme currently being
broadcast by the selected channel
appear alternately for 8 seconds
each.
SU BSID IARY SETTIN GS (cont.)
SELECT BAN D
Press % fi to change the
4
band between CH (regular)
and CC (cable), then
press
IN PUT CHAN N EL
O K
Press the NUMBER keys to input the channel number you
5
want to store.
● Input "0" before any single number entries.
● To input the registered station name (ID –
● For fine tuning adjustment, press
● When storing a channel that sends scrambled
● When "AV2 SELECT" is set to "AV2", the "DECODER"
EN TER N EW CHAN N EL
IN FO RMATIO N
pg. 4),
Press OK and the Confirmation screen appears.
pg. 48).
6
● Repeat steps
CLO SE CO N FIRMATIO N
SCREEN
Press M EN U .
7
● To change positions, see "Change Station Channel
● If you wish to set station names other than the ones
ATTEN TIO N
Guide Program numbers are not set when channels are
PR
CH
ID
08
C26 E-SP
stored manually. If an attempt is made at timer program-
09
55 WEST
ming with S
10
C24 SAT1
11
C23 OSF
screen appears; set the Guide Program numbers on this
12
– – – –
screen.
13
– – – –
Number Set" on pg. 27.
14
– – – –
Or perform " Guide Program Number Set" (
PR CH
.
12 CH01 – – – – +/–
#
[ 5 ∞ ] : SELECT
[
[MENU] : EXIT
The blueback screen and the
programme currently being
broadcast by the selected channel
appear alternately for 8 seconds
each.
press
until "----" (ID setting) begins blinking, then
#
press % fi .
blinking, then press % fi . While tuning, " +" or " –"
appears.
broadcasts, press
until "OFF" (Decoder setting)
#
blinks, then press %fi to set "DECODER" to "ON"
("OFF" is the default setting).
setting cannot be changed (
3 through 6 as necessary.
Position" (
pg. 51).
registered in your recorder,
page 52.
V
in this state, the " GUIDE PROG SET"
HOW
IEW
" ATTENTION – Regarding Guide Program
ID
FINE DECODER
OFF
] : CURSOR +=
: OK
pg. 53),
until "+/–" begins
#
pg. 39).
"Set Stations (B)" on
pg. 58).
Advertisement
Table of Contents
