Geemarc SOS-PRO295 User Guide

INTRODUCTION

!!! Please refer to our website: www.geemarc.com for an up to date user guide, as there may be important updates and changes you need to be aware of!!!

Use only the battery provided. There may be a risk of explosion if a wrong type of battery is used for the parent unit. The battery cannot be subjected to high or low extreme temperature and low air pressure at high altitude during use, storage or transportation. Disposal of battery into fire or a hot oven, or mechanically crushing or cutting or the battery can result in an explosion. Leaving the battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid of gas. Battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas. Dispose of used battery according to the instructions.
Normal operating temperature for the product (e.g. 0 ^oC ~ 40^oC).
Use only the adapters and battery listed below.
Power adapter information: Parent unit and baby unit output: 5V DC 1A. Vtech Telecommunications Limited Model: VT05EEU06045 (EU), VT05EUK06045 (UK)
Rechargeable Li-ion Battery: Model: GSP042535 3.7V, 320mAh, 1.184 Wh. Guangzhou Great Power Energy & Technology CO., Ltd

1. SOS : In idle mode, press to enter the emergency calling sequence set on your handset. In call mode: press and hold for 2 seconds to stop the emergency call.
2. : During a call: increase or increase the receiving volume level, during ringing: increase or decrease the ringer level. Press and hold for 2 sec to do a flash ® to answer a second incoming call ringing.
3. M1 dial the direct memory 1
4. M2 dial the direct memory 2
5. RESET
6. Microphone
7. Led indicator
   (Purple)
   • Steady On: Un-register.
   • Slow Flash: registered but the base is not available. Searching or out of range.
     (Blue)
   • Steady On: Seated in the base and fully charged.
   • Steady on 3s and emit a long beep: Successfully registered.
   • Double flashing: Off hook.
   • Double flashing and on for 2s when just off hook: Off hook but the signal is weak. Hear 3 rapid beeps in every 10s.
   • Short flashing: idle mode and off the charger, the pendant is in Standby mode.
   • Long flashing: idle mode and off the charger. Continuously flashing: ringing and can be heard.
     (Red)
   • In continue on the charger: The pendant charges.
   • Long flashing: The battery is low in using and we hear a short double beeps.
     (Red/Bleu)
   • Pairing mode after to hold and press the leys Vol(+) and Vol(-) during 10sec.
8. LOUDSPEAKER
9. CHARGER CONTACTS

Connection
Charger: Connect the power adaptor of the pendant in main power.

PACKAGE CONTENTS

1 cordless pendant SOS-PRO295,
1 pendant charger,
1 lanyard with breakout clip,
1 user guide.

Registration the Alarm pendant
On Base: press and hold /HANDSET LOCATOR on the base to enter the registration mode until to hear a beep.
On Alarm pendant: Press and hold VOL+ together with Vol- until the LED on pendant toggling between red and blue. Place the pendant unit close to the charger.
A long beep tone is generated and the LED is blue for a while if the registration is a success.

USE YOUR PENDANT

SOS Emergency calls
SOS Settings in handset
You need to set the SOS numbers in AMPLIDECT295SOS-PRO before you can make SOS emergency calls using the pendant. Using the handset:
Press LEFT SOFTKEY and ▲/▼ to select SOS SETTINGS.
Press LEFT SOFTKEY to show SOS NUMBER.
Press LEFT SOFTKEY and▲/▼ or SOS4)
Press LEFT SOFTKEY and enter a new number or edit the number stored already.
Press LEFT SOFTKEY to confirm or RIGHT SOFTKEY to delete
Press to come back in stand- by mode.

Make SOS Emergency Calls
Using the pendant:
Press SOS key on the pendant to enter the emergency calling sequence from the SOS 1 number to SOS 4 number (cycling 3 times). A call will be first dialed to the SOS 1 number. If the SOS 1 number does not answer in 60 seconds, the call be will made to the SOS 2 number, and so on.
Note: The other party when receiving SOS message, has to validate the call by pressing any keys. Then very 2mn need new validation to continue the conversation.

Direct Memory Keys
You can store direct memory numbers (M1 and M2) in the handset. Then, you can dial them directly from idle mode using the pendant.

Set Direct Memory Keys in Handset
Press LEFT SOFTKEY and ▼/▲ to select DIRECT MEM.
Press LEFT SOFTKEY and ▼/▲ to select the memory key to edit (M1 or M2).
Press LEFT SOFTKEY and enter a new number or edit the number stored already.
Press LEFT SOFTKEY to confirm.
Press to come back in stand-by mode.

Make Calls using Direct Memory Keys
Using the pendant:
Press M1 or M2 to dial the direct memory number stored.