Advertisement
WARNING! DO NOT use the washer on any material containing asbestos as this may release hazardous asbestos particles
F
into the atmosphere.
WARNING! DO NOT use the washer without a water supply. Dry running can seriously damage the unit.
F
DO NOT obstruct ventilation grills during operation.
&
DO NOT use the washer with flammable or toxic liquids or any other product. Only use recommended detergent. Non-recommended
&
detergents may corrode the machine cover and accessories.
DO NOT jam the trigger in the operating position.
&
DO NOT adjust any internal control valves, as they have been set at the factory.
&
DO NOT leave the washer running unattended.
&
DO NOT connect other appliances to the machine inlet or outlet.
&
DO NOT use in damp or wet weather conditions.
&
DO NOT move the unit by pulling the hoses or electrical cables. Use handle.
&
DO NOT touch plug with wet hands, to avoid the risk of electrocution. Keep all connections dry and off the ground.
&
DO NOT direct jet against yourself, other persons or animals, electrical equipment or the machine itself.
&
DO NOT use washer if you are tired, under the influence of alcohol, drugs or intoxicating medication.
&
DO NOT allow children or untrained persons to operate the washer.
&
WARNING! Discharge residual pressure before disconnecting the washer hose. Pressure left in unit may cause injury.
F
After use disconnect washer from electrical and water supplies and store in a safe, dry, childproof area.
"
2.
SPECIFICATION & CONTENTS
2.1. SPECIFICATION
Lance . . . . . . . . . . . . . . . .Rotating Nozzle
Manifold Pressure . . . . . . . . . . . . .1750psi
Effective Cleaning Pressure . . . . . .2950psi
Water Flow . . . . . . . . . . . . . . . . . .420ltr/h
Motor Power . . . . . . . . . . . . . . . . . .1800W
2.2.
CONTENTS
Unpack the product and check contents against the list below. Also check that the machine has an identification plate or label. If label or parts
are damaged or missing contact your supplier immediately.
DESCRIPTION OF ITEMS
Fig.1
1
Washer
2
Water Supply Fitting with Filter
3
Detergent Bottle
4
Rotary Lance
5
Gun with High Pressure Hose
6
Fan Nozzle
7
Rotary Nozzle
Fig.2
A
Feet
B
Elastic Strap
C
Support
D
Handle
E
Hose Reel Holder
F
Axle
G
Wheel x 2
H
C-clip x 2
I
Hub Cap x 2
J
Support
3.
ASSEMBLY
3.1.
Attach the two feet (fig.2.A) to the base of the washer using the screws provided.
3.2.
Attach each end of strap (fig.2.B) to the lugs on the support (fig.2.C) as shown in fig.3.
3.3.
Fit support (fig.2.C) and handle (fig.2.D) around top bar of washer, see fig.4. Secure with the two
screws provided, through the lower pair of holes in handle.
3.4.
Attach one half of the hose reel holder (fig.2.E) to the base of handle and the other half to the rear of the
washer, using the screws provided.
3.5.
Slide axle (fig.2.F) through hub of one wheel (fig.2.G), fit C-clip (fig.2.H) to groove in axle
(flat face towards wheel) and then press hub cap (fig.2.I) into wheel centre. See fig.5.
3.6.
Slide axle through mounting holes in rear base of washer, see fig.6, and then fit second wheel and hub
cap as in 3.4.
3.7.
Screw supply water fitting (fig.1.2) onto inlet port, on rear of washer just above axle. NOTE: This fitting
contains a filter, if an alternative fitting is used a suitable filter MUST be used.
3.8.
Attach the support (fig 2.J) to the handle using the screw provided.
fig. 4
Input Voltage . . . . . . . . . . . . . .230V
Motor Speed . . . . . . . . . . .2800rpm
Max. Inlet Temp . . . . . . . . . . . .60
Hose Length . . . . . . . . . . . . . .7.0m
Weight . . . . . . . . . . . . . . . . . . .13kg
fig. 1
By rotating the stream of water at
high speed, it is possible to increase
the effective cleaning pressure of
washer. We quote the pressure at
C
which the water leaves the pump as
O
‘Manifold Pressure’ and express the
cleaning power of the washer as the
‘Effective Cleaning Pressure’.
fig. 2
fig. 5
fig. 3
fig. 6
PC2950 - 2 - 050802
Advertisement
