Open House H634 Manual

OpenHouse
The H634 Cable/DSL Router with 4-port Switch
computers to a DSL or cable modem. "Plug and play" installation is easy when using

Typical Telephone DSL Installation

computers
4 3
H628
Cat-5
Termination
Hub
DSL connection
from telephone
company

Wiring the H634 Router

• Use only Category 5e unshielded twisted-pair cable for maximum
performance.
• When connecting to an H628 or a network device directly,
use straight through or crossover RJ-45 cables. All ports will
automatically detect the cable type.
• Each run to a network device should be less than 100 meters
(328 feet).

LED Indicators

• PWR lights when power from transformer is present.
• RDY lights when router is ready for packet data from the WAN.
• WAN lights when wide area network packets are sent or received.
• 1-2-3-4 lights when packet data is being sent to, or received from,
the client computers or additional hubs or switches.
Specifi cations: Typical @ 25°C ± 5°C
IEEE 802.3u

Compliance

IEEE 802.3
RJ-45 ports

Network Interface

RJ-45 WAN

Max Cable Length CAT-5e (UTP)

LED Indicators router & ports
operating

Environmental

temperature
output current

Power Supply

output voltage
input power
connects multiple
the H628 data hub. The H634 is
IEEE 802.3u 100 Base-TX Fast
Ethernet compliant, IEEE 802.3
10 Base-T compliant and has
activity LEDs for network status
and diagnosis. The H634 can
connect with up to four client
computers directly. Up to 253
computers can be connected
by using additional Ethernet
switches (H638) or hubs.
To From
DSL modem
7.5 VDC
from power
adapter
2 1 WAN DC IN
H634
Cable/DSL
Router
from 7.5 VDC
Power Adapter
DC
4 3 2 1 WAN IN
To data jacks in
remote wall plates.
Connect up to four
computers or external
hubs or switches.
DSL modem
Many modems may be
IN OUT
mounted by using an MB-55
or MB-56 mounting bracket
100 Base-TX, 10 Base-T and N-way
auto-negotiation
4 to client computers or hub/switch
1 from DSL/cable modem
100 meters (328 feet)
PWR, RDY, WAN, Ports 1, 2, 3, & 4
0°C to 40°C
1A maximum
7.5 VDC
120 VAC
Cable/DSL Router
®
ATTACH
HORIZONTAL
OR ATTACH
VERTICAL
DC Input
broadband
from cable
company

Using Additional Hubs or Switches for Expansion

• Use only Category 5e unshielded twisted-pair cable for maximum
performance.
• When connecting additional hubs or switches, use a straight
through or crossover RJ-45 Category 5e cable. Category 5 patch
cords may be used for short interconnections.
• The cable length between any two hubs or switches cannot
exceed 100 meters (328 feet).
• All additional hubs or switches used must be self-powered.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION
IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE
MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST
ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING
THAT MAY CAUSE UNDESIRED OPERATION.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used according to the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which if found by turning the
equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet other than the receiver's outlet.
• Consult a dealer or an experienced radio/TV technician for assistance.
ATTACH THE ROUTER TO
THE MB-56 MOUNTING PLATE
WITH THE DOUBLE-SIDED
FOAM TAPE SUPPLIED

Typical Broadband Cable Installation

To
computers
4 3 2 1
H634
Cable/DSL
Router
4 3 2 1 WAN
H628
Cat-5
Termination
Hub
to TVs
Filter
Cable modem
Splitter
IN OUT

Declaration of Conformity

PULL THE SNAP LATCH
PLUNGER OUT THEN
HOOK THE MOUNTING
PLATE INTO THE GRID
FROM THE BOTTOM
PRESS THE SNAP
LATCH PLUNGER
TO LOCK THE
PLATE
From
cable modem
7.5 VDC
from power
adapter
WAN DC IN
DC Input
from 7.5 VDC
Power Adapter
DC
IN
To data jacks in
remote wall plates.
Connect up to four
computers or external
hubs or switches.
Many modems may be
mounted by using an MB-55
or MB-56 mounting bracket
INTERFERENCE