Download
Share
Print this page
Two-Rock Custom Reverb Signature Owner's Manual
  1. Manuals
  2. Brands
  3. Two-Rock Manuals
  4. Amplifier
  5. Custom Reverb Signature
  6. Owner's manual

Two-Rock Custom Reverb Signature Owner's Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Two-Rock
Custom Reverb
Signature
(V1)
OWNERS MANUAL

Advertisement

loading
Need help?

Need help?

Do you have a question about the Custom Reverb Signature and is the answer not in the manual?

Questions and answers

Related Manuals for Two-Rock Custom Reverb Signature

Summary of Contents for Two-Rock Custom Reverb Signature

  • Page 1 Two-Rock Custom Reverb Signature (V1) OWNERS MANUAL...

  • Page 2: Dear Customer

    Dear Customer, Thank you for your purchase of a Two-Rock amplifier! As a discerning guitarist, you know the road to great tone begins with great components. Our classic design of carefully selected parts and hand-built approach combine to make an extremely versatile instrument.

  • Page 3: Front Panel Functions

    Front Panel Functions Input Jack- High impedance input to the amplifier. Plug in your instrument here. TREBLE - Adjusts the high frequency response. At lower settings of this control the tone will be warmer and smoother. As you turn this control up the highs become more prominent and aggressive adding gain to the signal as well.
  • Page 4 EQ1/EQ2 Switch - This switch lets you choose between 2 completely different global equalization settings greatly affecting the overall personality of the amplifier. EQ1 is a lower gain, higher headroom setting with extended midrange and bass response. This setting is suitable for any style requiring a pure clean tone with a nice round bottom end response, and plenty of headroom.
  • Page 5 CONTOUR - The contour control is an active wide band sweep. In the 12 o’clock position, the amp’s frequency response is flat. Counterclockwise rotation reduces high end response and increases low frequencies. Clockwise rotation decreases low end and increases the high frequency response.

  • Page 6: Rear Panel Functions

    Effects Loop – The effects loop on this amplifier is a “half active” type of loop, see FAQ on two-rock.com SEND - Use this jack to send the amplifier’s signal to the effects that you want to use in the loop.

  • Page 7: Fuse Chart

    FOOTSWITCH LEAD - Switches amp into lead mode BYPASS- Switches amp into a tone stack bypass mode FUSE CHART All Fuses are 3AG Type 250 Volt, SLO-BLO Export 100V: Domestic 120V: Export 220V, 230V, 240V: 3.5A 100 Watt 4x6L6 3.25A 100 Watt 4x6L6 1.6A 100 Watt 4x6L6 2.8A 50 Watt 2x6L6 2.5A 50 Watt 2x6L6...
  • Page 8 BIAS PROCEDURE: Make sure the speaker is connected properly, then power up the amplifier. Set the rear panel power mode switch to Full or Hi DO NOT apply any signal to the input during the biasing procedure! Insert volt meter’s positive probe into the bias test point socket (located underneath the chassis) Connect volt meter’s negative probe to chassis ground Switch amp out of standby and allow a few seconds for the circuit to stabilize Set voltmeter to millivolt scale (or lowest volt scale 60 millivolts =.060 volts.)
  • Page 9 We know your new Two-Rock amplifier will provide many hours of enjoyment and inspiration in the years to come. This manual is a resource for some of your questions. Please contact us with any other questions or comments that you may have. We look...
  • Page 10 Two-Rock Amplifiers, LLC 619 MARTIN AVENUE, SUITE 5 ROHNERT PARK, CA 94928 707-584-8663 www.two-rock.com SERIAL NUMBER: _____________________________...