Ascon tecnologic D7 line Instruction Manual

E
D7 line
Installation
manual
Table of contents

- General description;

- Model code;

- Electric safety;

- Installation kit;

- Installation;
- Electrical connections.
Simplified assembly and
connection
5
10
4
7
8
2
D 7 5 B C D -
Mod.
Line Basic
The product code indicates the specific hardware configuration of
the instrument, that can be modified by specialized engineers only.
Line
OP1-OP2 outputs
None
Relay - Relay
c c
Notes on electric safety and electromagnetic compatibility
Please, read carefully these instructions before proceeding with the installation of the controller
Class II instrument, rear panel mounting.
This instrument has been designed in compliance with:
Regulations on electrical apparatus: according to regu-
lations on the essential protection requirements in electri-
cal apparatus EN 61010-1
Regulations on Electromagnetic Compatibility:
according to
- Regulations on RF emissions:
EN61000-6-3: 2001 residential environments;
EN61000-6-4: 2001 industrial environments.
- Regulation on RF immunity:
EN61000-6-2: 2001 industrial equipment and system.
Ascon Tecnologic S.r.l.
viale Indipendenza 56,
27029 - Vigevano (PV)
Tel.: +39 0381 69871,
Fax: +39 0381 698730
www.ascontecnologic.com
1 DIN-rail, EN50022;
2 Spring loaded slide for rail fastening;
3 Side connector, build-in, to connect
one instrument to another (up to 31);
4 5-pole male connector, with screw
terminals, for power supply and
serial communications bus;
5 Four quick polarised connectors with
4 screw terminals for I/O;
Common power supply
3
1
0 F 0 0
Accessories
Serial communications
CanBus
RS485 Modbus/Jbus SLAVE
D 7
B Options
None
0
Retransmission OP5
1
It is important to understand that it's responsibility of the
installer to ensure the compliance of the regulations on safe-
ty requirements and EMC.
The repair of this instrument has no user serviceable parts
and requires special equipment and specialised engineers.
Therefore, a repair can be hardly carried on directly by the
user. For this purpose, the manufacturer provides technical
assistance and the repair service for its Customers.
Please, contact your nearest Agent for further information.
All the information and warnings about safety and elec-
tromagnetic compatibility are marked with the
sign, at the side of the note.
DIN rail mounting
data acquistion,
isolation, transmitter
D7 line
I n s t a l l a t i o n m a n u a l • 0 6 / 0 1 • C o d e : I S T R _ I _ D 7 _ E _ 0 3 _ - -
General description
6 Female connector, with termination
resistor for serial communications;
7 Three Output status leds (red);
8 Green Status led:
- ON: power on
- flashing: serial communications
in progress;
9 Couple of connector protections;
10 Wiring label;
11 Model identification label.
Withdrawable
4
Model code
B
1
Easy to replace even if
9
6
C User manual
Italian/English (std)
3
French/English
5
German/English
Spanish/English
D
0 0
5
Installation Kit
Each set of interconnected controllers requires one
model AD3-KIT/BA.RT.PC.CD kit:
Power supply and
5
serial comm.s
4
3
c o n n e c t o r
2
1
code AD3/BA
Connector with
termination resi-
stor for serial
c o m m . s
code AD3/RT
S E R I E S
c c
C US
U L
LISTED
powered
11
F
E
0 0
2 1
2
3
Couple of connec-
tor protections
code AD3/PC
CD Rom with
c o n f i g u r a t i o n
software tool
code AD3/CD