Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Glasdon Manuals
  4. Safety Equipment
  5. ORBITAL
  6. Installation and maintenance instructions manual

Glasdon ORBITAL Installation And Maintenance Instructions Manual

Chevron
Hide thumbs

Advertisement

Quick Links

Download this manual
INSTALLATION AND MAINTENANCE INSTRUCTIONS
IMPORTANT NOTE: ENSURE THAT ALL RELEVANT PERSONNEL HAVE THE RELEVANT QUALIFICATIONS/
CERTIFICATES AND ALL WORK IS CARRIED OUT IN ACCORDANCE WITH BS7671:2018/IET WIRING
REGULATIONS 18TH EDITION AND READ THESE INSTRUCTIONS PRIOR TO USE.
Please also refer to the 'Manual Handling Operations Regulations 1992' during the handling of the
product and materials used for installation. Glasdon recommends that a full Health and Safety
analysis and site survey is carried out prior to installation.
INSTALLATION INSTRUCTIONS
Signboard Installation
TYPE 1 - Socketed Installation
TYPE 2 - Extended Base Installation
KIT CONTENTS:
ITEM 1 - M8 Nyloc Nut
ITEM 2 - M8 x 30mm Washer
ITEM 3 - M8 x 75mm Bolt
ITEM 4 - Chevron Signboard
ITEM 5 - Stem Access Plug
ITEM 6 - Chevron Signcarrier
ITEM 7 - Glasdon Key
ITEM 8 - Stem Vent Plug
ITEM 9 - M8 x 20mm Bolt
ITEM 10 - M8 x 20mm Washer
ITEM 11 - Anchor Pin
ITEM 12 - Orbital Lockfast™ Socket Wedge x 1
ITEM 13 - Orbital Lockfast™ Socket
ITEM 14 - Orbital Lockfast™ Plug
ITEM 15 - Subsafe Cover Cap
ITEM 16 - M10 Nyloc Nut
ITEM 17 - M10 x 24mm Washer
ITEM 18 - Subsafe Underground Box
ITEM 19 - 5m Extension Cable
ITEM 20 - IP68 Connection Plug
Optional Extras
Splitter
Ducting Chamber
ORBITAL™
CHEVRON
See Page 2
See Page 4
See Page 7
TYPE 1 TYPE 2
x 6
x 6
x 6
x 6
x 6
x 6
x 1
x 1
x 2
x 2
x 1
x 1
x 1
x 2
x 2
x 4
x 4
x 1
x 1
x 1
x 2
x 4
x 4
x 4
x 4
x 4
x 4
x 1
x 1
x 1
x 1
x 2
x 2
11
14
15
16
17
20
1 of 10
5
8
8
9
12
11
13
14
18
19
DIAGRAM NOT TO SCALE
1
2
3
4
5
6
7
8
9
10
12
13

Advertisement

loading
Need help?

Need help?

Do you have a question about the ORBITAL and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Glasdon ORBITAL

Summary of Contents for Glasdon ORBITAL

  • Page 1 REGULATIONS 18TH EDITION AND READ THESE INSTRUCTIONS PRIOR TO USE. Please also refer to the ‘Manual Handling Operations Regulations 1992’ during the handling of the product and materials used for installation. Glasdon recommends that a full Health and Safety analysis and site survey is carried out prior to installation.
  • Page 2 (ITEM 4), using x3 bolts per rail. flat surface. So you have access to both sides of the signcarrier, ensure the front of the unit points upwards (Glasdon logo visible). When fitting the standard signboard, ensure the signboard Lower the signboard down on top of the signcarrier.

  • Page 3: Cable Connection Diagram

    IP68 Connection Plug Control Circuit IP Rated Cut-out OR IP68 Connection Plug Mains Supply DIAGRAM NOT TO SCALE ORBITAL INSTALLATION TOOLS/EQUIPMENT REQUIRED: - Excavation Equipment - Tape Measure - Spirit Level - 13mm Socket / Spanner - Concrete Mix (we suggest using a quick setting concrete i.e. QC10 for all installations).
  • Page 4 Subsafe and power supply source and the Subsafe to the lay a depth of 50mm of gravel or sand in the base of the hole Orbital socket, thread the following cables: 1. Power supply for drainage. Adapt the excavation to suit cable entry/exit from the source to the Subsafe 2.
  • Page 5 GROUND LINE SIGNCARRIER SOCKET LEFT HAND SOCKET Feed cable from the socket through the ducting to the Thread the extension cable through the left hand socket and underside of the Subsafe and thread cable through the gland out of the connection point. We recommend attaching a piece into the box, tighten well.
  • Page 6 Insert the signcarrier into the sockets and slide forwards to Fill all excavations with concrete. Ensure concrete is flush lock into position. The Orbital Chevron should face forwards to with the top of the sockets and the fill level on the Subsafe match the front facing sockets.
  • Page 7 50mm of gravel or sand in the base of the hole for drainage. Choose a suitable location to install the Subsafe Orbital stem, thread the following cables: 1. Power supply from the source to the Subsafe 2. Circuit cabling from the Subsafe to relative to the signcarrier to suit site requirements.
  • Page 8 Position the box using a spirit level to ensure that the top is Thread one side of the IP68 rated plug onto the end of the level with the indicator line, to provide a flush installation. extension cable and the other end onto the ‘supply out’ cable Add/remove gravel as required to level.

  • Page 9: Operator Instructions

    FRONT Push / slide the signcarrier back in the sockets. To remove socket wedges, fully insert the Glasdon key into key track, twist slightly to allow the wings of the key to grip the underside of the keyhole and pull the wedges out from each socket.
  • Page 10 GLASDON cannot be held responsible for claims arising from incorrect installation, unauthorised modifications or misuse of the product. Stock No. C000/1044 - DWG No. 02B-093-15 Issue 1 - October 2022 © Copyright 02/2022 Glasdon UK Ltd reserve the right to alter specifications without prior notice. 10 of 10...