Table of Contents
Advertisement
Quick Links
Hand-held Welding Head Manual
Model No.：BWT15
Declaration
1. Shenzhen qilin laser application co., ltd. may update the operating instructions at
any time due to software or hardware upgrades. These updates will be included in the
new version of the operating instructions.Read the instructions carefully before using
the welding system !
2.
Purchase Qilin laser handheld welding system to enjoy a lifetime of software
upgrade service, in the stipulated warranty scope, shenzhen qilin laser to fulfill the
promise of warranty service.It is strictly prohibited to disassemble or repair this
product by personnel other than our company without permission. In case of any
damage caused by the above factors, our company will not provide any free warranty
service.The company shall not be liable for any loss which may result from the use of
the product.The contents contained in the operating instructions shall not be modified
or reproduced by any organization or individual by any means. Shenzhen Qilin Laser
Application Technology Co., LTD has the right to interpret the product description.
Shenzhen Qilin Laser Application Technology Co., Ltd.
Advertisement
Table of Contents
Related Manuals for Laser BWT15
Summary of Contents for Laser BWT15
- Page 1 Model No.：BWT15 Declaration 1. Shenzhen qilin laser application co., ltd. may update the operating instructions at any time due to software or hardware upgrades. These updates will be included in the new version of the operating instructions.Read the instructions carefully before using...
-
Page 2: Security Information
Important information that needs to be paid attention to when using a product. Do not ignore this information, which provides useful operational assistance. This label indicates laser radiation. It is usually affixed to the laser output product. Be careful of laser when using such equipment. -
Page 3: Technical Parameters
Collimating length 50 (D20F50*3.5) Focal length 150 (D20F50*3) Protective lens D20X2 Cooling Way Water Weight 1.2 kg Working Mode Operating instruction The signal status is displayed in the page: FGAP Fillings Welding Connect Motor Shenzhen Qilin Laser Application Technology Co., Ltd. -
Page 4: Working Mode
FGAP : Control of laser switch. When in normal use, turn on FGAP button to connect laser light signal. ( Connection of laser source will be cut down after 15 minutes of no working) Gas : For gas control, install proportional valve, effective percentage control. -
Page 5: Proportional Valve
Power Setting for slowly rising & falling 1. Control laser power slowly rise and fall to protect protective lens and better welding effective. 2. Rising to full power in the time you set slowly, can be chosen from 20-400ms 3. - Page 6 1. Adjust the Axis of X and Y motor reflecting lens to change the red light offset position. 2. The adjustment radius of the laser center point is 5mm. 3. Make sure all motor circruit are normal before adjustment to avoid wrong operation.
- Page 7 Connection Definition Controller Connection Shenzhen Qilin Laser Application Technology Co., Ltd.
-
Page 8: Power Interface
The HMI port is defined as a 5-pin green terminal through which the mainboard supplies power and communicates with. Signal Definition Description Output power,500mA HMI power supply Power ground HMI sender Serial port communication TXD signal HMI receiver Serial port communication RXD signal Shenzhen Qilin Laser Application Technology Co., Ltd. - Page 9 Laser control interface The laser interface is an 8 PIN green terminal +4PIN green terminal +RS232 interface. * The table shows the definition of laser source interface. Signal Definition Description PWM+ MOD+ Duty cycle is adjustable from 1%-100%, 24V and 5V can be switched...
- Page 10 Used to protect the gas blowing Connect to control, negative pole negative pole of 24V relay SS_1 Wire feeder trigger signal 1 Wire feeder control signal SS_2 Wire feeder trigger signal 2 Wire feeder control signal Shenzhen Qilin Laser Application Technology Co., Ltd.
- Page 11 Only when the welding torch nozzle and the safety clamp are connected, one of the essential conditions of laser out will be achieved. *The table is the definition of the control system interface of the wire feeder...
- Page 12 NO IPG Laser control PWM, EN, RED, NC output 24V signal except IPG NO IPG LPC except IPG Power adjustment: DA 1 analog voltage can be adjusted from 0 to 10V Shenzhen Qilin Laser Application Technology Co., Ltd.
- Page 13 9. The laser head is installed with a digital motor, must be used gently, to prevent motor failure. 10. When the laser head is not in use, please repeatedly use the system gas to blow air, so that the dust is discharged, and remove the copper nozzle, seal with sealing tape, install the copper nozzle to blow air more than 2 times before using.
- Page 14 4. All pistol integral cases, brass nozzles, stainless tubing, wire feed brackets, etc. are not covered by this warranty. If it is necessary to carry out repairs aboard, the travelling expenses shall be paid by the customer. Shenzhen Qilin Laser Application Technology Co., Ltd.