Advertisement
Quick Links
Hand-held Welding Head Manual
Model No.：BWT15
Declaration
1. Shenzhen qilin laser application co., ltd. may update the operating instructions at any time due
to software or hardware upgrades. These updates will be included in the new version of the
operating instructions.Read the instructions carefully before using the welding system !
2. Purchase Qilin laser handheld welding system to enjoy a lifetime of software upgrade service, in
the stipulated warranty scope, shenzhen qilin laser to fulfill the promise of warranty service.It is
strictly prohibited to disassemble or repair this product by personnel other than our company
without permission. In case of any damage caused by the above factors, our company will not
provide any free warranty service.The company shall not be liable for any loss which may result
from the use of the product.The contents contained in the operating instructions shall not be
modified or reproduced by any organization or individual by any means. Shenzhen Qilin Laser
Application Technology Co., LTD has the right to interpret the product description.
Advertisement
Related Manuals for Laser BWT15
Summary of Contents for Laser BWT15
- Page 1 Model No.：BWT15 Declaration 1. Shenzhen qilin laser application co., ltd. may update the operating instructions at any time due to software or hardware upgrades. These updates will be included in the new version of the operating instructions.Read the instructions carefully before using the welding system ! 2.
- Page 2 After changing the structure of head and the position of the trigger button, it can be used for both left and right hands. 9. QBH protective cover: connect with the laser end, pay attention to cleaning during installation to avoid dust entering the gun body.
-
Page 3: Technical Parameters
Technical parameters Interface type Power Range 2000W Laser Wavelength 1064-1080 Mark Width 0.2-5.0 mm Collimatinglength focal length 120/150 Protective lens D20X2 Cooling Way Water Weight 1.2 kg Working Mode Operating instruction The signal status is displayed in the page: FGAP... - Page 4 Control of laser switch. When in normal use, turn on FGAP button to connect laser light signal. ( Connection of laser source will be cut down after 15 minutes of no working) Gas : For gas control, install proportional valve, effective percentage control.
- Page 5 1. Adjust the Axis of X and Y motor reflecting lens to change the red light offset position. 2. The adjustment radius of the laser center point is 5mm. 3. Make sure all motor circruit are normal before adjustment to avoid wrong operation.
-
Page 6: System Controller
Multi-language and Lock Settings Muti-language: Chinese-English-Russian-Korean-Vietnamese S/N: Serial Number of Machine Version: Controller version of system Available life: Valid use time (when (-) shows mean a permanent use permission) License: the License number if needs to be entered when lock or unlock machine System Controller Shown as above pic:... -
Page 7: Protective Function
Protective Function 1. Laser head protection: when the laser head appears (E) signal or no data output, the system detects the motor fault, the laser head status light goes out, and the system stops sending out the light signal.Torch status can be lit, but trigger is not valid. - Page 8 24V GND Reserve 24V output Adjust the analog voltage from 0 to 10V adjustable Adjust the gas proportional valve 0-10v Trim port Adjust the analog voltage from 0 to 10V switch Laser power control, analog output switching 10V or 4V...
- Page 9 Laser connection definition Raycus Board Port FEIBO LIANPIN 1000X/24 pin 1000W/25 pin PWM+ GATE PWM+ 15 调制+ MOD+ PWM+ 调制+ PWM- PWM- 调制 - 16 调制 - MOD- MWM- EX-EN 18 使能+ 6 使能+ 外部出光+ GDA-IO 20 使能- 9 使能- 外部出光-...
-
Page 10: Faq And Troubleshooting
FAQ and troubleshooting 1. The state of the laser head is not displayed: X.Y motor cable is loose, or 15V power input is interrupted, or the motor is damaged. 2. No on state display or intermittent light output during welding: it may be that the communication signal is not connected or the wire is loose and not plugged tightly, and the crocodile clamp does not form a loop with the X5 signal.Intermittent light may be due to the... - Page 11 3. Continuous power interruption will cause damage to the welding control system, please provide continuous and reliable power supply! 4. The external safety lock is 24V high level. Please do not make short connection with the GND shell of the aviation plug of the system sheath, or pay no attention to the collision during installation, otherwise the short circuit may burn the power supply or the main control board.