Electrolux RH36WCT6GS Use & Care Manual Installation Instructions
Vent hood
Hide thumbs
Also See for RH36WCT6GS:
- Factory parts catalog (4 pages) ,
- Product specifications (2 pages) ,
- Design manual (164 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Electrolux RH36WCT6GS
Summary of Contents for Electrolux RH36WCT6GS
-
Page 1: Installation Instructions
Use & Care Guide Installation Instructions Vent Hood 04307838/2N - 08/2007... -
Page 3: Table Of Contents
Please read and save this guide Thank you for choosing Electrolux, the new premium brand in home appliances. This Use & Care Guide is part of our commitment to customer satisfaction and product quality throughout the service life of your new appliance. -
Page 4: Safety
Safety Important Safety Instructions Read all instructions before using this appliance. Save these instructions for future reference. Do not attempt to install or operate your appliance until you have read the safety precautions in this manual. Safety items throughout this manual are labeled with a WARNING or CAUTION based on the risk type. - Page 5 TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:* 1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
-
Page 6: Verify Package Contents
Verify package contents Unpack hood and check contents. You should receive: 1 - Hood 1 - Decorative Flue Assembly 1 - Parts Bag containing: 1 - Mounting Bracket 1 - Discharge Collar 1 - Flue Mounting Bracket 6 - Mounting Screws (4,8 x 38mm Pan Head) 7 - Mounting Screws (3,9 x 9,5mm Pan Head) 2 - Mounting Screws (3.9 x 6mm Flat Head) 6 - Drywall Anchors... -
Page 7: Installation
Install the ductwork To reduce the risk of fire, use only metal ductwork. 1. Decide where the ductwork will run between the hood and the outside. 2. A straight, short duct run will allow the hood to perform most efficiently. 3. -
Page 8: Wiring
Installation Wiring This range hood must be properly grounded. The unit should be installed by a qualified electrician in accordance with all applicable national and local electrical codes. GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. -
Page 9: Install Mounting Bracket
Install mounting bracket 1. Construct wood wall framing that is flush with inte- rior surface of wall studs. Make sure: a) the framing is centered over installation loca- tion. b) the height of the framing will allow the mounting bracket to be secured to the framing within the dimensions shown. -
Page 10: Prepare The Hood
Installation Prepare the hood NOTE On stainless steel hoods, carefully remove the plastic protective film from all exterior surfaces of the hood and decorative flues, prior to final installation. 1. Remove the polystyrene block and the tape (Fig.1). 2. The back plate shown in Fig. 2 must be removed: remove the (4) screws of the back plate, operating from the inside of the hood (Fig. - Page 11 DUCTED CONFIGURATION 1. Install the discharge collar into the duct connector of the range hood. Fig. 6. DISCHARGE COLLAR DUCT CONNECTOR Installation NON- DUCTED CONFIGURATION NOTE The following materials must be purchased separately for non-ducted recirculation installations: Non - Ducted Recirculation Kit, Model DFKTWC75GS. 5”...
-
Page 12: Install The Hood
Installation Install the hood NOTE At least two people will be required to mount the hood. 1. Raise the hood into its mounting position. 2. Align the rectangular opening on the back of the hood with the wall-mounting bracket. Gently lower the hood until it securely engages the bracket. - Page 13 9. Carefully place the decorative flue on the hood. Fig. 13. - On ducted installation in rooms with 8-foot ceilings, the air vents are concealed. Install the flue with the air vents down. - On non-ducted installations in rooms with 8-foot ceilings, the air vents are exposed. Install the flue with the air vents up.
-
Page 14: Install Filters
Installation Install filters (DUCTED AND NON-DUCTED HOODS) 1. To remove the GREASE filters, pull the metal latch tab outside and unlock the filter. 2. To install the GREASE filters, align rear filter tabs with slots in the hood. Depress the metal latch tab, push filter into position and release. -
Page 15: Maintenance
Proper maintenance of the Range Hood will assure proper performance of the unit. Grease filters The grease filters should be cleaned when the filter reset switch will be illuminated. Use a warm detergent solution. Grease filters are dishwasher safe. See “INSTALL FILTERS” section for removal and installation instructions. -
Page 16: Operation
Operation Controls Dead-front mode Stand-by mode In dead-front mode, press any key for enter in stand- by mode. If the hood is in stand-by mode, after 10 seconds on return automatically in dead-front mode. Light switch Press any key for enter in stand-by mode. Push the light switch once to turn the lights ON to a dim level. -
Page 17: Halogen Bulbs
Halogen bulbs This range hood requires two halogen bulbs (max 20W, 12V, Type T3 bulb, G4 Base). Halogen Bulb Key : 5304454951 ALWAYS SWITCH OFF THE ELECTRICITY SUPPLY BEFORE CARRYING OUT ANY OPERATIONS ON THE APPLIANCE. To change bulbs: 1. Open the cover by prying from the proper slots. - DO NOT ROTATE. -
Page 18: Warranty Information
This warranty only applies in the 50 states of the U.S.A., Puerto Rico and Canada. Product features or specifications as described or illustrated are subject to change without notice. All warranties are made by Electrolux Home Products North America, a division of White Consolidation Industries, Inc.