3M Quiet Space QuietSP-SIOC - Bluetooth Headphones Quick Start Guide

Getting Started

1. Indicator light
   Off Headphones off
   White Quiet Space™ mode
   Blue Bluetooth ® mode
   Red Low battery
   Yellow Charging
   Green Fully charged
2. Mode button
   On/Off
   Press and hold for 3 second
   Switching modes
   Press to switch between Quiet Space™ and Bluetooth™ mode
3. Volume controls
   Press – to decrease volume and + to increase volume
4. Action button
   In Quiet Space™ mode
   When the indicator light (1) is white, you are in Quiet Space™ mode Quiet Space™ mode provides three levels of sounds that are engineered to mask unwanted noises and allow you to get your work done
   Press to cycle through low, mid and high Quiet Space™ sounds
   In Bluetooth® mode
   Press to play/pause music
   Quickly press twice to advance track
   Quickly press three times to skip back
   For phone calls, press to answer or hang up; hold to decline an incoming call
5. 3.5 mm Audio Input
6. Microphone
   For phone calls and teleconferencing

Auto Shut-off

Bluetooth / Audio Input mode

5 minutes after either Bluetooth ® or the audio input is disconnected, the headphone automatically powers down

Quiet Space mode

After 4 hours of inactivity in Quiet Space™ mode, the headphone automatically powers down

After Auto Shut-off, press and hold the power button for 3 seconds to turn the headphones on

Pair Device

In Bluetooth^® mode, press and hold the action button for 3 seconds You will hear "Bluetooth^® Pairing " Make sure your Bluetooth^® enabled device is scanning/ searching for devices Check your device to make sure it has discovered 3M™ Quiet Space Select to connect to the headphones

Once paired

Once paired, you will hear, "Pairing Successful"

Once Connected

Once connected, each time you turn on the headphones, it will automatically link to your device and say, "Bluetooth^® Connected"

Bluetooth Range

The typical range between a Bluetooth^® enabled device and the 3M™ Quiet Space™ Headphones is approximately 25 feet This distance depends on the device As the distance between the Bluetooth^® enabled device and the headphones increases the risk of the signal dropping also increases

For best results, keep the audio device on your body or within an arm's length of the 3M™ Quiet Space™ Headphones while using Bluetooth^® mode

Additional Info

Quiet Space mode

When the indicator light (1) is white, you are in Quiet Space™ mode. Quiet Space™ mode provides three levels of sounds that are engineered to mask unwanted noises and allow you to get your work done.

Bluetooth mode

When the indicator light (1) is blue, you are in Bluetooth^® mode.

To play your first song

• Press and hold the action button (4) to pair a new device
• Select 3M™ Quiet Space Headphones in your device's Bluetooth^® menu
• Play a song from your favorite music app on your device

Voice and Video Calls

Integrated microphone lets you make and take phone calls hands-free. Quiet Space™ Headphones are compatible with most video-conferencing platforms

Charging

To comply with the regulatory guidelines, your headphones have been shipped to you with only a partial charge on its integrated lithium ion battery.

To charge the headphones
Insert the supplied USB-C connector cable into the USB-C jack located on the bottom of the left cup of the headphones.

Connect the other end of the cable to a suitable USB-C +5 Volt power source such as a computer or third party certified (UL, Intertek, etc.) AC to USB-c +5 Volt wall adapter.

The indicator light will be yellow while charging and change to green when complete

Product takes approximately 4 hours to charge fully

Note: Do not attempt to use product while charging or while the charging cable is connected

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download 3M Quiet Space QuietSP-SIOC - Bluetooth Headphones Quick Start Guide