3M Peltor Lite-Com Pro II Quick Reference Manual

Peltor Lite-Com Pro II Product Range
MT7H7F4010-EU-50 with headband
MT7H7B4010-EU-50 with neckband
MT7H7P3E4010-EU-50 with helmet attachment for Peltor G22 and G3000 hardhats.
(A rear plate is also included for helmet attachments for the Peltor G2000 hardhat.)
Technical Data
Frequency range:
FCC:462.5625MHz~467.7125MHz, 406.1 - 430,440 - 470MHz,LPD:433.05 - 434.79 MHz(Note:LPD only used in Europe)
CE:PMR
Operation mode: Simplex
Channels: Max. 30
Channel raster:
Channel separation:
FCC/IC: 12.5 kHz CE: 12.5 kHz/ 25 kHz
Modulation:
(FM)
FCC/IC: 2.5 kHz
CE: 2.5 kHz/ 5kHz
FM (16K0F3E / 8K50F3E)
Microphone type: Electret (MT53) or dynamic (MT7)
Receiver sensibility: Typical -122 dBm
Selective squelch: Programmable (and supports CTCSS and DCS)
Output power: 200 / 20 / 10 mW ERP
Range: Outdoors up to 3 km depending on conditions
Power consumption: Stand-by: ca 55 mA
Receiving: ca 65 mA
Transmission:
Low power: ca 100 mA
Medium power: ca 115 mA
High power: ca 200 mA
Operating time at conditions
10/10/80 TX/RX/Standby at 20°C: Hi output power: ca 14 hours
Mid output power: ca 16 hours
Low output power: ca 17 hours
Operating temperature: -20°C to +55°C
Storage temperature: -40°C to +55°C
Weights including ACK08 battery: MT7H7F4010-**-50: 540 g
MT7H7B4010-**-50: 500 g
MT7H7P3E4010-**-50: 540 g
ACK08 technical information
Charging time: approx. 10-12 hours (no visible charging indicators for ACK08)
Capacity: 3,7 V, 1350 mA, 5 Wh
Charging cable: AL2AH (fused 200mA)
After charging cycle is finished charger automatically turns into maintenance charging mode.
ACK08 must be charged with AL2AH connected to a certified 5V SELV power supply such as 3M, Peltor battery charger
FR08. Power supply must be able to deliver a minimum of 200 mA.
3M Occupational Health &
Environmental Safety Division
© 3M 2012. All rights reserved.
3M Svenska AB, Box 2341
3M™ Peltor™ Lite-Com™ Pro is made in Sweden by
SE-331 02 Värnamo 3M Svenska AB, SE-331 02, Värnamo, Sweden.
Sweden
Phone: +46 (0) 370 65 65 65
3M, Peltor and Peltor Lite-Com are trademarks of 3M Corporation,
Fax: +46 (0) 370 65 65 99
St. Paul, MN 55144-1000, USA
Email: peltorcommunications@mmm.com
Internet: www.3M.com/Peltorcomms Please recycle. Printed in Sweden.
Peltor Lite-Com Pro II
™ ™
The Sound Solution
MT7H7F4010-EU-50
MT7H7B4010-EU-50
MT7H7P3E4010-EU-50
403 – 470 MHz
Quick reference guide
Key Function
MODE Switches the Lite-Com Pro II on and off.
Choose between the functions in the menu.
UP (+) Increases the level of the selected function.
DOWN (–) Decreases the level of the selected function.
PTT Transmits with the Lite-Com Pro II.
E)
Attenuation (with head band)
Frequency (Hz) 125 250 500 1000 2000 4000 8000 H M
Mean attenuation (dB) 14.7 23.4 30.7 34.6 34.5 36.9 37.3
St. dev. (dB) 3.9 4.6 3.2 3.4 3.1 2.7 4.2 33 dB 27 dB
APValue (84%) 10.8 18.8 27.4 31.2 31.4 34.2 33.1
Attenuation (with neck band)
Frequency (Hz) 125 250 500 1000 2000 4000 8000 H M
Mean attenuation (dB) 15.5 23.3 31.2 35.6 35.0 36.5 40.9
St. dev. (dB) 2.6 2.3 2.0 3.2 3.4 3.4 3.3 33 dB 29 dB
APValue (84%) 13.0 21.0 29.2 32.4 31.6 33.2 37.6
Attenuation (with helmet attachment)
Frequency (Hz) 125 250 500 1000 2000 4000 8000 H M
Mean attenuation (dB) 16.2 22.9 31.7 35.6 34.5 37.7 40.0
St. dev. (dB) 3.2 2.2 2.0 2.9 3.0 3.9 3.3 33 dB 29 dB
APValue (84%) 13.0 20.7 29.7 32.7 31.5 33.8 36.8
Mean attenuation (dB) = Average attenuating characteristics at given frequency
St. dev. (dB) = Standard deviation at given frequency
APV (dB) = Assumed Protection Value. Average attenuating characteristics minus standard deviation at given frequency.
H = Average attenuation characteristics in the higher frquency spectrum
M = Average attenuation characteristics in the mid range frequency spectrum
L = Average attenuation characteristics in the higher frequency spectrum
SNR = Single Number Rating
MT53H7F470-50
MT53H7B470-50
MT53H7P3E470-50
L SNR
19 dB 30 dB
L SNR
21 dB 31 dB
L SNR
21 dB 31 dB