Download Print this page
Airflow Vector Snorkel Kit S014 Quick Start Manual

Airflow Vector Snorkel Kit S014 Quick Start Manual

For the dodge ram 2500 and power wagon (5.7l hemi)

Advertisement

Quick Links

Airflow Vector Pty Ltd
4 Collins Rd, DROMANA VIC. 3936
AUSTRALIA
Ph: +61 3 5987 3733
www.airflowvector.com
Instructions to fit the Snorkel Kit S014
for the Dodge Ram 2500 and Power Wagon (5.7L HEMI)
1.0 Introduction
Airflow Vector Pty Ltd thanks you for your purchase and the trust you put in our
products.
We strive to supply our customers with the highest quality equipment based on
the most efficient design and best styling. We are confident that you will enjoy
using our Snorkel system.
It should improve the power of your vehicle as well as reduce its fuel
consumption.
1.1 General instructions
Follow carefully the instructions listed on these pages and use the template
provided, do not over tighten bolts. Do not use silicone on any connections,
use mastic.
Ensure that safe work practices are followed when installing your Airflow
Snorkel. Protective ear and eye wear should be worn at all times when using
power tools.
1.2 Disclaimer
It is highly recommended that installation is undertaken by a qualified
mechanic or body shop. Airflow Vector will not be held responsible for any
damage incurred through incorrect fitment of the templates and workmanship.
It is the responsibility of the fitter to ensure that particular care is taken when
assembling the Snorkel kit to the vehicle as it may cause damage to the
windscreen and or electrical components. Safe work practices must be used at
all times when undergoing installation.
We guarantee Airflow Vector's kits against manufacturing defects as long as
proof of purchase can be established.
All models produced by Airflow Snorkels are verified to suit right hand drive
vehicles according to Australian specifications. Variations in vehicle
specifications may occur in other markets.
If you're in doubt about the product suitability, please forward a photograph of
the engine bay, air filter housing and of the vehicle at frontal/side position to
info@airflowvector.com
SD014US (S014 Instructions booklet).doc
21 March 2011
Page 1 of 16
\\Server\d\AirflowSnorkels\Products\Snorkels\S14\SD014US (S014 Instructions booklet).doc

Advertisement

loading
Need help?

Need help?

Do you have a question about the Snorkel Kit S014 and is the answer not in the manual?

Questions and answers

Summary of Contents for Airflow Vector Snorkel Kit S014

  • Page 1 Dodge Ram 2500 and Power Wagon (5.7L HEMI) 1.0 Introduction Airflow Vector Pty Ltd thanks you for your purchase and the trust you put in our products. We strive to supply our customers with the highest quality equipment based on the most efficient design and best styling.
  • Page 2: List Of Components

    Airflow Vector Pty Ltd 4 Collins Rd, DROMANA VIC. 3936 AUSTRALIA Ph: +61 3 5987 3733 www.airflowvector.com 2.0 List of Components S014 Kit content Fasteners included Designation Length Unit Designation Snorkel SP183 A Pillar S014 SP151 Dodge Ram SP026 Screw Plug Nylon SP063 Air Ram 3.5"...
  • Page 3: Detailed Instructions

    Airflow Vector Pty Ltd 4 Collins Rd, DROMANA VIC. 3936 AUSTRALIA Ph: +61 3 5987 3733 www.airflowvector.com 2.1 List of tools and additional parts required Masking tape, clear tape, black mastic, hammer, centre punch Assorted screw drivers, sockets and spanners 4”...
  • Page 4 Airflow Vector Pty Ltd 4 Collins Rd, DROMANA VIC. 3936 AUSTRALIA Ph: +61 3 5987 3733 www.airflowvector.com Remove the air intake and Locate the connector SP184 discard it. as shown Drill six 5/32” holes in the Please wear gloves connector SP184 (2 on the...
  • Page 5 Airflow Vector Pty Ltd 4 Collins Rd, DROMANA VIC. 3936 AUSTRALIA Ph: +61 3 5987 3733 www.airflowvector.com 3.13 Read the template carefully 3.16 Cut the internal tapping areas to allow sticking the 3.14 Cut the template out along template very close to the...
  • Page 6 Airflow Vector Pty Ltd 4 Collins Rd, DROMANA VIC. 3936 AUSTRALIA Ph: +61 3 5987 3733 www.airflowvector.com 3.23 Pre-drill all holes at ¼” (5 3.24 Drill the two top snorkel snorkel mounting holes, 1 air mounting holes at ½” and intake hole) the three lower at 3/8”...
  • Page 7 Airflow Vector Pty Ltd 4 Collins Rd, DROMANA VIC. 3936 AUSTRALIA Ph: +61 3 5987 3733 www.airflowvector.com 3.29 Peel off the rubber seal from 3.30 Fit temporarily the snorkel the A Pillar SP151 to allow the marking of the “A” pillar bracket 3.31 Using the bracket as a...
  • Page 8 Airflow Vector Pty Ltd 4 Collins Rd, DROMANA VIC. 3936 AUSTRALIA Ph: +61 3 5987 3733 www.airflowvector.com 3.35 File the holes with a square 3.36 Paint ALL raw metal file to suit nylon plugs SP026 surfaces with Zinc rich primer (5 snorkel fixing holes, 1 air intake hole, 2 “A”...
  • Page 9 Airflow Vector Pty Ltd 4 Collins Rd, DROMANA VIC. 3936 AUSTRALIA Ph: +61 3 5987 3733 www.airflowvector.com 3.45 Smear some sealant inside 3.47 While holding the elbow the elbow SP135B SP135B under the guard, connect the snorkel SP151 3.46 Slide a hose clamp SP018 on...
  • Page 10 Airflow Vector Pty Ltd 4 Collins Rd, DROMANA VIC. 3936 AUSTRALIA Ph: +61 3 5987 3733 www.airflowvector.com 3.52 Slide the TRP hose through 3.54 Put back the modified air the inner guard inside the box base assembly in the engine bay engine bay 3.53 Slide a hose clamp SP018 on...
  • Page 11 Airflow Vector Pty Ltd 4 Collins Rd, DROMANA VIC. 3936 AUSTRALIA Ph: +61 3 5987 3733 www.airflowvector.com 3.59 Slide the hose clamp SP018 3.60 Slide the air ram SP063 onto on the snorkel SP168 the snorkel 3.61 Ensure that the top of the...
  • Page 12 Airflow Vector Pty Ltd 4 Collins Rd, DROMANA VIC. 3936 AUSTRALIA Ph: +61 3 5987 3733 www.airflowvector.com 4.0 Optional pre-cleaner (not included in this kit) Remove the Air Ram SP063 Install Pre-cleaner filter sock SP065B Air sock should neatly fit into...
  • Page 13 Airflow Vector Pty Ltd 4 Collins Rd, DROMANA VIC. 3936 AUSTRALIA Ph: +61 3 5987 3733 www.airflowvector.com Polish with silicone cleaner 5.0 Improvement program We strive to produce documentation and kits free of mistakes, however, should you discover any error or omission, please let us know by quoting the initials shown in the box overleaf.
  • Page 14 Airflow Vector Pty Ltd 4 Collins Rd, DROMANA VIC. 3936 AUSTRALIA Ph: +61 3 5987 3733 www.airflowvector.com This page is left intentionally blank Page 14 of 16 21 March 2011 SD014US (S014 Instructions booklet).doc...
  • Page 15 Airflow Vector Pty Ltd 4 Collins Rd, DROMANA VIC. 3936 AUSTRALIA Ph: +61 3 5987 3733 www.airflowvector.com This page is left intentionally blank SD014US (S014 Instructions booklet).doc 21 March 2011 Page 15 of 16...
  • Page 16 Airflow Vector Pty Ltd 4 Collins Rd, DROMANA VIC. 3936 AUSTRALIA Ph: +61 3 5987 3733 www.airflowvector.com This kit has been carefully packed by Date Initials Note: The content of this manual may be modified from time to time to ensure that improvements brought to our kits are described accurately.