Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Insta 228
Summary of Contents for Insta 228
- Page 1 MNL90009 Rev. M 07.21.14 MODEL 228 OPERATION AND MAINTENANCE MANUAL...
-
Page 2: Safety Summary
FOR USE BY QUALIFIED PERSONNEL ONLY Safety Summary International Symbols WARNING In case of power cord damage, Power Off do not attempt to repair or replace the power cord. Contact the manufacturer or the local Power On distributor. WARNING Hot Surface Hot Surface. - Page 3 Read this manual. Keep it with your machine; it's your key to proper operation and lasting Insta shall not be liable for the injury, loss or service. damage, direct or consequential, arising out of the use or the inability to use the product.
-
Page 4: Installation
Digit solid objects Digit moisture Non protected Non protected Specifications Objects greater Dripping water than 50mm MODEL 228 Dripping water Objects greater when tilted up to Voltage 120 Volts AC 50/60 Hertz than 12mm 15 deg. Model 228 1750 Watts 14.6 Amps... -
Page 5: Operation
Environmental Conditions position, away from lower platen. (See Solid State Controller section) Only operate Insta heat seal machines under 3. Allow the machine to warm up until the suitable environmental conditions. selected temperature is reached. - Page 6 FOR USE BY QUALIFIED PERSONNEL ONLY Operation Timer/Temperature Temperature Control NOTE Fahrenheit/Centigrade (Celcius) Conversion Press MODE button until counter is displayed, then push and hold the SET and MODE button until level 1 Sleep Mode set back time appears (1.OFF), then choose Level 1 °...
-
Page 7: Sleep Time
1._XX ; XX = Minutes from OFF to 99 Insta heat seal machines. During activation, any disturbances such as the key press or heat press cycle will reset the... -
Page 8: Automatic Shut Off
FOR USE BY QUALIFIED PERSONNEL ONLY User Offset Automatic Shut Off 9. Press MODE. 5. Press MODE. 10. Press SET + UP or DOWN Arrow to 6. Press SET + UP or DOWN Arrow to set the Offset. set Auto Shut Off Time. 5._XX ;... - Page 9 Since mineral spirits are flammable, use precautions and keep away from sparks, flame, or hot heat platen. 5. The Model 228 machine requires periodic lubrication with a high-temperature, non- melting grease (MPPL023). A. Lubricate the post, handle and cam assembly depending upon usage.
-
Page 10: General Maintenance
FOR USE BY QUALIFIED PERSONNEL ONLY Replacement of Silicone Rubber General Maintenance Pads It is recommended that you have the following 1. Make sure heat platen is cool. items available: 2. Use tube of MPPC006 silicone adhesive A. Regular screw driver sealant to bond the silicone rubber pad to B. - Page 11 FOR USE BY QUALIFIED PERSONNEL ONLY Safety and Danger Zone Diagram Do not handle the machinery with wet hands Hot Surface. Avoid contact with Upper Platen Shroud and Aluminum Casting Machinery should be operated Keep hands clear under a secure flat surface...
- Page 12 GREEN/YELLOW BLUE WHITE WHITE YELLOW GRAY PURPLE WHITE WHITE...
- Page 14 MPSP2200 MPSP2200 57 CAM MPSC220 MPSC220 58 SCREW, BUTTON HD 5/16-18 x 1.00 LONG MHSB516181 MHSB516181 59 NUT, HEX JAM 5/16-18 MHNHJ51618 MHNHJ51618 60 O'RING MPSS273 MPSS273 63 FEET, RUBBER (4/SET) MPF90004 MPF90004 66 BASE MPSB204 MPSB204 MODEL 228 0721...
- Page 15 MPL90175 MPL90175 A1 PLATEN, HEAT ASSY MPP228A1A MPP228A2A A2 LUG PIN ASS'Y MPP90141 MPP90141 A3 HANDLE, PRESSURE ASS'Y MPSH515 MPSH515 A4 PLATEN, LOWER ASSY MASP007 MASP007 A5 CAM/PRESSURE LEVER ASSY MPSC201 MPSC201 A6 BASE ASSY MPSB204A MPSB204A MODEL 228 0721...
- Page 16 FOR USE BY QUALIFIED PERSONNEL ONLY...
- Page 17 FOR USE BY QUALIFIED PERSONNEL ONLY...
- Page 18 FOR USE BY QUALIFIED PERSONNEL ONLY 13925 E. 166 St. • Cerritos, CA USA 90702 • (800) 421-6971 • Fax (562) 404-3010 Parts Orders • (800) 426-3609 • (562) 404-3000 Ext 215 Parts Orders • (800) 426-3609 • (562) 404-3000 Ext. 215 Technical Support •...
Need help?
Do you have a question about the 228 and is the answer not in the manual?
Questions and answers