Advertisement
Quick Links
Advertisement
Related Manuals for Karol KUT
Summary of Contents for Karol KUT
- Page 1 Installation Manual...
- Page 2 After implementing suitable protection measures, if it is not possible to operate with the power supply disconnected, the electrical installer is able to operate in the presence of live parts inside cabinets or electrical boxes. ATTENTION Karol Italia srl disclaims all liability in case of wrong installation.
-
Page 3: Table Of Contents
ENGLISH CONTENTS Cabinets installation ________________ Pag.4-5 Connections between cabinets _________ Pag.6 Drawer adjustment __________________ Pag.7 Shelf and towel-holder installation ______ Pag.8-9 Drawer-with-organizer installation ____ Pag.10-11 Tall units installation _________________ Pag.12 Mirror cabinet “Move” _______________ Pag.13 SLIM version installation _____________ Pag.14 Installation Boiserie _________________ Pag.15... -
Page 4: Cabinets Installation
● The dowels and the screws supplied by Karol can be used or not at the installer’s descretion ( this depends on the type of wall where the cabinet should be mounted). - Page 5 CABINETS INSTALLATION Hooking the bracket STEP 2 Image 1 ● Lean the cabinet against the wall and and hook it to the plates on the wall usign the hanger fitting of the cabinet (see image 1) (Image. 1). ● Adjust the height of the cabinet (see image 2) ●...
-
Page 6: Connections Between Cabinets
CONNECTIONS BETWEEN CABINETS Case 1 Two or more cabinets H.36 cm ● Use the metal joints “B” supplied by Karol in the holes “A” in the cabinets’ sides (see image 1) ● Tighten the joints “B” Image 1 ATTENTION There are 6 holes in the cabinets’ sides. -
Page 7: Drawer Adjustment
Drawer adjustment Cabinet Adjust the drawer/s using the mechanisms indicated in the images here below. Im. 1 Im. 2 Im. 3 Image1 Image 1 - Height adjustment (up-down) of the drawer front To adjust the vertical distance of the drawer from the cabinet . -
Page 8: Shelf And Towel-Holder Installation
55mm ATTENTION The dowels and the screws supplied by Karol can be used or not at the installer’s descretion (this depends on the type of wall where the cabinet should be mounted). 50 mm STEP 2 ●... - Page 9 SHELF AND TOWEL-HOLDER INSTALLATION INSTALLATION OF THE SHELF ATTENTION Hook the shelf with the brackets “B” (already mounted Check the side (right or left) where to fix the bracket. on the shelf) to the plates “A” which have just been mounted on the wall and tighten the screw “C”...
- Page 10 DRAWER-WITH-ORGANIZER INSTALLATION INSTALLATION STEPS STEP 1 ● Open the drawer as much as possible. Unfasten the drawer using the mechanism under the drawer. STEP 2 ● Place the bracket “A” on the wall (with the help of a spirit level or similar) mark with a pencil the position of the holes to be drilled. Remove the bracket and drill the holes on the wall.
-
Page 11: Drawer-With-Organizer Installation
STEP 1 View of the cabinet with the brackets shown as they are supplied by Karol ATTENTION The dowels and the screws supplied by Karol can be used or not at the installer’s descre- tion (this depends on the type of wall where the cabinet should be mounted). -
Page 12: Tall Units Installation
TALL UNITS INSTALLATION STEP 1 Place the bracket “A” on the wall (with the help of a spirit level or similar) and mark with a pencil the position of the holes to be drilled (see image 1,2). Remove the bracket and drill the holes on the wall. Place again the bracket on the wall and apply the dowels and the screws in all the holes (see image 1). -
Page 13: Mirror Cabinet "Move
ATTENTION STEP 2 The dowels and the screws supplied by Karol can Hook the mirror cabinet though the hangers “B” (already be used or not at the installer’s descretion (this mounted) to the bracket “A” which has been previously... -
Page 14: Slim Version Installation
SLIM VERSION INSTALLATION STEP 1 Open the drawer completely. Image of the unit Unfasten the drawer using the mechanisms under the Position of middle bracket unit. Remove the drawer. Position of the side bracket Position of the side bracket STEP 2 Put the cabinet on the requested height using a bubble level. - Page 15 BOISERIE WALL-PANEL INSTALLATION STEP 1 Place the bracket “A” on the wall (with the help of a bubble level) and mark with a pencil the position of the holes to Use a bubble level be drilled (see image 1). Remove the bracket and drill the holes on the wall. Place again the bracket on the wall and apply the dowels and the screws in all the holes.
- Page 16 Karol Italia srl - Loc. Belvedere, 6 53034 Colle Val d’Elsa (Siena) Italy P.IVA 00586170938 - REA SI 202939 www.karol.it - karol@karolitalia.it Rev. 09_2019...