Advertisement

1
.
........................................................................
2-1 Specifications & Features........................................................
3-1 Keyboard.............................................................................
3-2 Indication meaning .................................................................
4
.
4-1 Power on and Power off.....................................................
4-2 Calibration...............................................................................
4-3 Zero...................................................................................
4-4 Weighing...........................................................................
4-5 Tare...................................................................................
4-6 Power saving.....................................................................
4-7 Battery...............................................................................
4-8Charging...........................................................................
4-9 Parameter setting...............................................................
..............................................................................
5-1 Normal notes........................................................................
5-2 For sealed lithium battery.......................................................
Content
.......................................
1
1
2
2
2
3
3
3
4
4
4
4
4
5
5
7
7
7

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the JWI-520 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Jadever JWI-520

  • Page 1: Table Of Contents

    Content Introduction ……………………………………………………………… 2.Product Introduction 2-1 Specifications & Features……………………………………………….. 3 Keyboard and indication meaning ………………………………… 3-1 Keyboard………………………………………………………………….. 3-2 Indication meaning ……………………………………………………….. Operations 4-1 Power on and Power off…………………………………………….. 4-2 Calibration………………………………………........4-3 Zero……………………………………………………………………….. 4-4 Weighing………………………………………………………………… 4-5 Tare……………………………………………………………………….. 4-6 Power saving…………………………………………………………… 4-7 Battery……………………………………………………………………. 4-8Charging…………………………………………………………………...
  • Page 2: Introduction

    1. Introduction This manual contains installation and operation instructions for the JWI-520 weighing indicator. please read the manual completely before installation and operation. 2. Product Introduction 2-1 Specifications & Features 2-1-1 Specification of JWI-520 Stainless Steel Indicator: Model JWI-520 Version...
  • Page 3: Keyboard And Indication Meaning

    2-1-2 Basic data of full Stainless Steel Platform: Plate 2828 3040 4050 5060 6080 size(cm) Waterproof and dustproof IP68 grade Capacity(kg) 15/30/60 30/60/150 60/150/300 60/150/300 150/300/600 Load cell 150×90×74 150×35×40 150×44×40 150×60×62 150×60×62 size(mm) side hole 2-1-3 Working temperature: -5~+35℃ 2-1-4 Storage temperature: -25~50℃...
  • Page 4: Operations

    Err-03 When calibration, the placed weight is too small and it refuses to calibrate. (Weight should more than 10% max. capacity) Overload, show this as the weight over 100%FS+9e, with the DING sound. - - - - Then you should reduce the weight. 4.
  • Page 5: Zero

    The reason is: weights are too small or input wrong value. 4-3 Zero When without tare, the weight display is ≤4% Max. capacity. Press <ON/ZERO> and the display shows “ 0 ”, ”ZERO” Lamp lighting. 4-4 Weighing Put weight to pan, and it shows the weight, lamp lighting.
  • Page 6: Parameter Setting

    Put the plug in the socket, is charging lamp. is lighting when charging. Show voltage:after power on and on“0”, at the same time press <ON /ZERO> and <TARE > three seconds, now show the battery voltage, press <SET/0~9> to exit. 4-9 Parameter setting Press <SET/0~9>...
  • Page 7 4-9-2-2 Counting: when it displays “pcs”, press<tare>. Now “pcs” lamp lighting. Longtime press <on/zero>, it displays count and return to 0. Then put the sample (as much as possible, but don’t more than max.capacity). After stable, press <tare>. Press <set/0~9> to add values and press<tare>to choose.
  • Page 8: Notes

    4-9-9-1 Stainless steel indicator Opening the back over of indicator , welding the leads of load cell by color , ring the welding point with heat shrinkable tube , contraction after heating , then place all the lines into sealing bowl , fix the lines and sealing by 704 glue , air dry after 1 hour .

Table of Contents