Advertisement
Installation
Before Installation
If the device is generally DC-receiving and does not support the POE
function, the POE-PD04S+ can easily be used to accept POE source
power and apply it separately from DC output power.
The POE-PD04S+ separates the power out and provides three kinds of
DC power output through its DIP switch and its voltage and current
shown as below:
DIP Switch :
• 12 VDC / 2.25A (Max)
• 19 VDC / 1.42A (Max)
• 24 VDC / 1.125A (Max)
Cables Installation
POE-PD04S+ provides a POE-powered solution for non-IEEE
802.3af/at devices.
The setup of the splitter can be performed using the following steps:
Connect from "DATA OUT" of POE-PD04S+ to the RJ-45 port of
the remote device.
Make sure first power source that the POWER+DATA in Port of
the splitter is fully connected to the 802.3at source-powered
PoE Injector or PoE Switch.
Connect the correct DC plug from "DC OUT" of POE-PD04S+ to
the DC port of remote device. (Use a DC cable to connect
devices that are to be powered by DC)
Caution: Please ensure the output voltage is correct for
remote device. Otherwise it will damage your remote
device.
Power on the remote device and the LED for voltage status
indicator on POE-PD04S+ will remains on.
Units Combination
This device can be locked on the wall, (Does not have screw
attachment, you must prepare it yourself) or it can be
combined with multiple units for easy to bundles organize the
Ethernet cables.
LED Indicator :
Output power switching (12VDC / 19VDC / 24VDC)
LED indicators for Power function enable
DC 12V output: 12V Light on
LED Definition
DC 19V output: 19V Light on
DC 24V output: 24V Light on
Product Specifications
Standards & Hardware Specifications
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3ab 1000BASE-T
Standard
IEEE 802.3bz 2500/5000BASE-T
IEEE 802.3at Power over Ethernet (PoE+)
IEEE 802.3af Power over Ethernet (PoE)
10BASE –T: UTP Cat. 3 or up
Network Media
100BASE-TX : UTP Cat. 5 or up
1G/2.5G/5GBASE-T : UTP Cat.5e or up
10M/100M/1G/2.5G/5G (Half-duplex),
Data Transfer Rate
20M/200M/2G/5G/10G (Full-duplex)
Data PIN
PIN 1/2, 3/6 & 4/5, 7/8
End-span (Type-A): PIN 1/2,3/6 ;
Power PIN
Mid-span (Type-B): PIN 4/5,7/8
Data In
Connects PC/HUB/Switch
RJ-45 x1 for Power + Data input
Ethernet Connector
RJ-45 x1 for Data output
ESD Protection
Over Voltage protection &Short Circuit Protection
Environmental & Mechanical Characteristics
Max Power
Active POE 802.3at : Up to 27Watts
Output
Passive POE : Up to 80Watts
Power Interface
DC-Jack : Output to any none PoE 12V or 19V or
24V DC in device
Power Requirement
Active PoE 802.3af/at Power Source or
Passive PoE Max to 90W Power Source
PoE Input Voltage
44V~57V
DC Output
12V/19V/24V three range adjustable by DIP
Control Range
switch
When PSE is Active POE :
Max 12V/2.25A , 19V/1.42A, 24V/1.125A
DC Output Current
When PSE is Passive POE :
Max 12V/4.17A , 19V/3.94A, 24V/3.33A
LED Indicators
DC Output LED x3 : 12V or 19V or 24V
Operating
0° to 55° C
Temperature
Storage Temperature -40° to 70° C
Operating Humidity
10% to 90% non-condensing
Storage Humidity
5% to 90% non-condensing
Dimension
80.5 x 80 x 39.5mm ( W x D x H )
Unit Weight
100.2g
Case of Materials
ABS
Production Location
TW
Certification
FCC, CE, RoHS-compliant
Advertisement
