Cerio POE-PD06S User Manual

POE-PD06S
10/100/1000M/Multi Gigabit 802.3bt Class8 to
DC12-24V PoE Splitter
User's Guide
FCC Certifications
This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received; including
interference that may cause undesired operation.
CE Mark Warning
This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022 class A for ITE,
the essential protection requirement of Council Directive 89/336/EEC on the approximation of the laws of the
Member States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be possible that information in this document
is not up-to-date. Please check with your local distributors for the latest information. No part of this document can be
copied or reproduced in any form without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective companies.
Copyright © 2016, All Rights Reserved.
Unpacking Information
Thank you for purchasing our PoE series products. Before installation,
please check that your package contains the following items.
Open the shipping cartons of the splitter and carefully unpack its
contents. The carton should contain the following items:
1. POE-PD06S Main Unit x 1
2. Inside diameter 2.1mm(PHY) to 2.1mm DC Cable x 1
3. Warranty Card x 1
4. Quick Installation Guide x 1
Hardware Overview
Introduction
POE-PD06S is designed to run Multi Gigabit speed PoE cables
over long distances. This device splits the PoE signal into separate
data and power sources and relays them into non-PoE devices.
Supports DC output voltage 12V, 19V and 24V via DIP switch three
range adjustable. Using the PoE Splitter, you can take Wireless AP / IP
Cameras / VoIP Phone where power outlets are not readily available.
It delivers Power over Ethernet to remote devices. The PoE Splitter
can be used to compatible any 802.3bt PoE++/ 802.3at PoE+/802.3af
PoE switch, Proprietary injector unit to provide small to
medium-sized businesses with a complete end-to-end PoE solution.
Product Application
Highlight Features
Complying with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX,

IEEE 802.3ab 1000Base-T, IEEE 802.3bz 2500/5000 BASE-T, IEEE
802.3af PoE, IEEE 802.3at PoE+ and IEEE 802.3bt PoE++
standards.
Supports 1 / 2.5 / 5Gbps Multi Gigabit Ethernet.

The POE-PD06S can use to connect non-PoE IEEE 802.3bt/at

/af powered devices to PoE Switch or PoE injector.
Supports Output Voltage hot switching for 12VDC, 19VDC,

24VDC three range adjustable.
When using Active or Passive PoE 90Watts or up as input, the

maximum power output: DC24V/80Watts, DC19V/72Watts,
DC12V/50Watts output.
Supports Ethernet PoE to separate to only DC/Power and only

Ethernet/Data.
Supports power reverse acute protection design, and auto

restarts to protect possible short circuit, which can reduce the
damage caused by the short circuit.
LED indicators for Power function enable and DC output

voltage display of 12V/19V/24V.
Bundle accessories for inside diameter 2.1 mm (PHY) to 2.1

(PHY) mm DC cable.
Durable metal case design supports desktop and wall

mounting installation.
v1.0