Related Manuals for Kobold KLP
Summary of Contents for Kobold KLP
- Page 1 Operating Instructions Butterfly Isolating Valves with Pneumatic Actuator Model: KLP...
-
Page 2: Table Of Contents
Dimension ....................16 Disposal ...................... 17 EC Declaration of Conformance ..............18 Manufactured and sold by: Kobold Messring GmbH Nordring 22-24 D-65719 Hofheim Tel.: +49(0)6192-2990 Fax: +49(0)6192-23398 E-Mail: info.de@kobold.com Internet: www.kobold.com page 2 KLP K05/0123... -
Page 3: Note
Please read these operating instructions before unpacking and putting the unit into operation. Follow the instructions precisely as described herein. The instruction manuals on our website www.kobold.com are always for currently manufactured version of our products. Due to technical changes, the instruction manuals available online may not always correspond to the product version you have purchased. -
Page 4: Regulation Use
4. Regulation Use Any use of the Butterfly Valves with Pneumatic Actuator, model: KLP, which exceeds the manufacturer’s specifications, may invalidate its warranty. Therefore, any resulting damage is not the responsibility of the manufacturer. The user assumes all risk for such usage. -
Page 5: Personal Advice
Observe the respective relevant professional safety and accident prevention regulations when carrying out the mounting / repair work. Check the correct functioning of the safety equipment (for example the emergency push off buttons/ safety valves, etc)! KLP K05/0123 page 5... - Page 6 (230 V AC~) can be touched! Therefore, the adjustments must be carried out only by an electrician or a person having adequate training, who is aware of the potential hazard! page 6 KLP K05/0123...
- Page 7 After completing the maintenance or repair, check for correct functioning of the armature/valve and the tightness of the pipe connections. Also check the functioning of the accessories e.g. actuators, limit switches, etc. KLP K05/0123 page 7...
-
Page 8: Device Safety
After finishing the assembling and adjustments check for proper functioning of the armature/valve and the tightness of the pipe connections. Also check the functioning of the accessories e.g. actuators, limit switches, etc. page 8 KLP K05/0123... -
Page 9: Pneumatical Installation
Pass the hoses to its Basic position, if so possible, within conduits or cable ducts. As an alternative to the shown variant the control of the actuator could be carried out by a directly mounted pilot valve. KLP K05/0123 page 9... -
Page 10: Function "Double-Acting
Insert a hose into the fitting at port “P2“ which will supply the actuator with compressed air during the closing operation. Tighten the hoses in the fittings at port “P1“and “P2“. Check the tightness of all connections. page 10 KLP K05/0123... -
Page 11: Function "Single-Acting
Tighten the hose in the fitting at port “P1“. Check the tightness of all connections. This completes the mounting and the pneumatical installation of the actuator. KLP K05/0123 page 11... -
Page 12: Pneumatical Disassembly
The butterfly valve will be opened or closed by using the actuator. Do not clasp – under any circumstances – onto the actuating element or insert any parts into the actuating element. Heavy injuries or damages will be the consequence. If necessary, install a protection device. page 12 KLP K05/0123... -
Page 13: Adjustments/Starting
Fix the adjustment screws by tightening the nuts (1). Ensure that the adjustment screw will not turn. Check the adjustment and if necessary, correct it. At this point the adjustment of the pneumatic actuator is completed. KLP K05/0123 page 13... -
Page 14: Starting
Actuate the pneumatic actuator via “control by hand” and check the correct functioning of the actuator and the mounted slide/valve/flap. Check all pipe connections for tightness. Check all the control lines for tightness. Check the functioning of the accessory units. page 14 KLP K05/0123... -
Page 15: Maintenance
Depending on the environmental and operating conditions the replacement of the sealings and guide rings may be necessary from approx. 500.000 up to 1.000.000 switching operations. Appropriate spare part kits are available. KLP K05/0123 page 15... -
Page 16: Technical Information
11. Technical Information Operating instructions, data sheet, approvals and further information via the QR code on the device or via www.kobold.com 12. Order Codes Operating instructions, data sheet, approvals and further information via the QR code on the device or via www.kobold.com 13. -
Page 17: Disposal
(Cd, Hg, Li or Pb) of the heavy metal that is decisive for the classification as containing pollutants: 1. „Cd" stands for cadmium 2. „Hg" stands for mercury 3. „Pb" stands for lead 4. „Li" stands for lithium Electrical and electronic equipment KLP K05/0123 page 17... -
Page 18: Ec Declaration Of Conformance
15. EC Declaration of Conformance We, KOBOLD Messring GmbH, Hofheim-Ts, Germany, declare under our sole responsibility that the product: Butterfly Isolating Valves with Pneumatic Actuator Model: KLP-... to which this declaration relates is in conformity with the standards noted below:...
Need help?
Do you have a question about the KLP and is the answer not in the manual?
Questions and answers