Download Print this page

Advertisement

Quick Links

Installation
Installation
Fire risk and danger of damage
from appliances which give off heat.
Appliances which give off heat can
catch fire and set fire to the
refrigeration appliance.
Do not place appliances which give
off heat, such as mini-ovens, double
burner hobs or toasters on the
refrigeration appliance.
Fire risk and danger of damage
from open flames!
Open flames can set fire to the
refrigeration appliance.
Keep open flames (e.g. a candle)
away from the refrigeration
appliance.
Side-by-side installation
Risk of damage due to
condensation on the external
appliance panels.
In environments with high humidity,
condensation can build up on
external appliance panels, which can
cause corrosion.
Do not place different refrigeration
appliance models directly next to
one another.
If the model number for your
refrigeration appliance does have the
letter S in it, it can be installed side-by-
side. Your refrigeration appliance is
equipped with built-in heating units in
the side panels.
Please contact Miele for information on
which combinations are suitable for
your appliance.
11210790-04
Location
This appliance should be installed in a
dry, well-ventilated room.
When deciding where to install your
appliance please bear in mind that it will
use more energy if installed near a
heater, cooktop or other appliance that
gives off heat. Direct sunlight should
also be avoided.
The higher the room temperature, the
longer the compressor will run and the
higher the energy consumption will be.
When installing the appliance, please
note:
- The mains socket must not be
located directly behind the appliance
and must be easily accessible.
- The plug and cable must not touch
the rear of the appliance as they
could be damaged by vibrations from
the appliance.
- Nor should other appliances be
plugged into a socket located directly
behind this appliance.

Advertisement

loading

Summary of Contents for Miele KS 28463 D

  • Page 1 S in it, it can be installed side-by- side. Your refrigeration appliance is equipped with built-in heating units in the side panels. Please contact Miele for information on which combinations are suitable for your appliance.
  • Page 2 *INSTALLATION* 11210790-04 Installation Ventilation  Risk of damage due to condensation on the external  Risk of fire and damage due to appliance panels. insufficient ventilation! In environments with high humidity, If the refrigeration appliance is not condensation can build up on ventilated sufficiently, the external appliance panels, which can compressor will run more frequently...
  • Page 3 *INSTALLATION* 11210790-04 Installation Fitting the supplied wall spacers Limiting the opening angle of the door The wall spacers supplied must be The door hinges are set at the factory to used in order to achieve the stated enable the door to be opened up to energy consumption values and to 115°.
  • Page 4 *INSTALLATION* 11210790-04 Installation  Remove cover  from the door hinge and cover  from the soft-close mechanism.  Undo and remove the screw  on the soft-close mechanism  and insert a screwdriver behind the soft- close mechanism.  Remove the soft-close mechanism . – Fitting the door opening angle ...
  • Page 5 *INSTALLATION* 11210790-04 Installation – Fitting the soft-close mechanism  Fit the cover  on the door hinge.  Insert the soft-close mechanism   Fit the panel  so that it clicks into on the door hinge side (at an angle position. initially) until it clicks into position. ...
  • Page 6 *INSTALLATION* 11210790-04 Installation Installation Aligning the appliance  Two people are required for installing the appliance.  The appliance must be empty to be installed.  Move the appliance carefully on floors that are sensitive to scratching  To align the appliance, adjust the to prevent damage.
  • Page 7 *INSTALLATION* 11210790-04 Installation Supporting the appliance door Installing the appliance in existing kitchen units  Risk of damage and danger of  injury due to the appliance door Risk of fire and damage due to swinging open or the refrigeration insufficient ventilation! appliance tipping over.
  • Page 8 *INSTALLATION* 11210790-04 Installation The larger the ventilation gap, the more economically the compressor will work. - A ventilation gap of at least 50 mm depth must be provided at the back of the appliance behind the whole width of the top box for air to circulate.
  • Page 9 *INSTALLATION* 11210790-04 Installation Appliance dimensions * Dimensions without wall spacers fitted. Appliance depth is increased by 15 mm with the wall spacers supplied fitted. [mm] [mm] KS 28463 D ed/cs 1,850 1,815...
  • Page 10: Changing The Door Hinging

    *INSTALLATION* 11210790-04 Installation  Remove the shelves/bottle shelf from Changing the door hinging the appliance door. The appliance is supplied with right- hand hinging. If left-hand hinging is Removing the top covers required, the hinges must be changed.  Open the appliance door. Please note that the hinging must not be changed if this appliance is going to be installed side by side with another...
  • Page 11 *INSTALLATION* 11210790-04 Installation Removing the upper soft-close Removing the door mechanism  Danger of injury when removing the appliance door! The door is not secure as soon as the pin has been removed from the door hinge. The door must be held by a second person.
  • Page 12 *INSTALLATION* 11210790-04 Installation Changing over the lower hinge plate  Secure the hinge plate  on the opposite side, starting with screw  in the middle at the bottom.  Pull the hinge pin  complete with  Then screw in the other two washer and adjusting foot upwards to screws .
  • Page 13 *INSTALLATION* 11210790-04 Installation Changing over the upper door hinge  Slide the cover  off to the side.  Turn the cover 180° and refit it on the opposite side. Slide on the cover from the side and click it into position.
  • Page 14 *INSTALLATION* 11210790-04 Installation Preparing the upper door Useful tip: Place a suitable cover over a stable surface to protect the appliance door from damage. Place the door on it with the outside facing down. Changing over the door opening aid ...
  • Page 15 *INSTALLATION* 11210790-04 Installation  Refit the door opening aid  on the  Secure the door opening aid using opposite side. the screw with the plastic collar  and the screw without plastic The plastic lug on the slider must not collar . Do not overtighten the abut the door seal.
  • Page 16 *INSTALLATION* 11210790-04 Installation Changing over the soft-close mechanism If you want to limit the door opening angle to approx. 90° you need to fit the door opening angle limiter supplied before refitting the soft-close mechanism (see “Installation - Fitting the door opening angle limiter”). ...
  • Page 17 *INSTALLATION* 11210790-04 Installation Refitting the door  Use your fingers to insert the pin  into the door bearing bush.  Screw in the pin  (by approx. ¼ turn) until it clicks into position.  Fit the safety cover  onto the pin. ...
  • Page 18 *INSTALLATION* 11210790-04 Installation Securing the soft-close mechanism Fitting the upper covers  Open the door 90°.  Fit the cover  on the door hinge.  Fit the panel  so that it clicks into position.  Slide on the cover  until it clicks into position.
  • Page 19: Aligning The Appliance Door

    *INSTALLATION* 11210790-04 Installation Aligning the appliance door Electrical connection The appliance door can be aligned with The appliance must only be connected the appliance housing after it has been using the connection cable supplied fitted. (AC 220–240 V, 50 Hz supply). In the following illustration the door is not shown in the closed position to make it easier to see what you have to To align the appliance door, use the...
  • Page 20 *INSTALLATION* 11210790-04 Installation The socket must not be concealed Do not connect the refrigeration behind the appliance and must be appliance to a stand-alone inverter such easily accessible so that the appliance as those used with an autonomous can be quickly disconnected from the energy source, e.g.
  • Page 21 *INSTALLATION* 11210790-04 Installation Connecting the appliance  Insert the plug connector at the back of the appliance into the socket. Make sure that the plug connector has clicked into position correctly.  Insert the mains plug into the mains socket and switch on. The appliance is now connected to the electricity supply: ...