Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for iglooworks IoT Deadbolt
Summary of Contents for iglooworks IoT Deadbolt
- Page 1 Installers & User guide IoT Deadbolt. Version 0.3 09/21...
- Page 2 In the meantime, you should follow us on Facebook and Youtube! Like us on Facebook Visit our Youtube As our iglooworks app is frequently updated, there may be changes to this manual. Please refer to our website iglooworks.co/support for the latest version of the manual.
-
Page 3: Table Of Contents
Table of Contents What’s Included Specifications Installation Guide Requirements Prepare Door for Installation Prepare Lock for Installation Installation Instructions Test Lock Prepare the Door Frame User Guide Lock Anatomy Features Unlocking and Locking Lock Pairing & Provisioning Lock Behaviour 9V Jumpstart Physical Keys Audio and LED Indications Troubleshooting... -
Page 4: What's Included
What’s Included Back Plate Back Assembly Back Assembly Front Assembly Rubber Gasket & Rubber Gasket AA Alkaline Batteries x8 Strike Plate Housing & Bolt Assembly Screw Holder Strike Plate 6mm (0.24”) 4mm (0.16”) 8mm (0.31”) Keyhole Bolt Screw x1 Bolt Screw x2 Bolt Screw x4 Cover x1 Construction Keys x4... -
Page 5: Specifications
Specifications Model IoT Deadbolt Battery Type 8 x AA* Alkaline Battery Life Up to 1 Year Emergency Power 9V Alkaline Battery Operation Temp -20°C to 55°C Storage Temp -40°C to 70°C IP Rating IP65 Material AI, Zinc Alloy, ABS Weight Net: 1.7kg, Gross: 2.2kg... -
Page 6: Installation Guide
Installation Guide Requirements Clearance Door Thickness Measurements 43mm (1.69”) to 60mm (2.36”) 10mm (0.39”) 20mm (0.78”) >110mm (4.33”) for 60mm (2.38”) / >120mm (4.72”) for 70mm (2.75”) backset 50mm (1.96”) -
Page 7: Prepare Door For Installation
Please ensure that there is an existing handle on your door for push - pull access. Not for: metal gates, glass doors or sliding doors. If you are unsure if your door is suitable, send us web links to your door pictures to info@iglooworks.co... - Page 8 How to use the Drill Sheet Drilling (Door) Fold here Make sure this is before drilling aligned to the centre holes for side of door edge 10mm (0.39“) Drill Bit 25mm (0.98”) Spade Bit 54mm (2.12”) Hole Saw Door edge 54mm (2.12”) Chiselling 2.7mm (0.11”)
-
Page 9: Prepare Lock For Installation
Prepare Lock For Installation Set Back Assembly for Left / Right Hand Installation Left Hand Installation Set the toggle to ‘L’ for Hinge left-hand installation * Hinge is on your left. Outside Right Hand Installation Set the toggle to ‘R’ for Hinge right-hand installation * Hinge is on your right. -
Page 10: Installation Instructions
Installation Instructions Measure If you are replacing your current deadbolt lock, industry standards are 60mm (2.38”) or 70mm (2.75”) backset. To determine which backset length you should use, measure the distance (x) between the center of 54mm (2.12”) hole to door edge. 54mm (2.12”) Hole... - Page 11 Install bolt and front assembly on the door The ‘+ ‘ hole on the bolt assembly should be in the middle of the hole. If possible lubricate the ‘+’ hole before inserting the tailpiece. It is advisable to lubricate the ‘+’ hole before inserting the tailpiece Screw Holder Please ensure the tailpiece is in horizontal...
- Page 12 Measure and cut the tailpiece if necessary After inserting the tailpiece, measure the distance of protrusion from the door. Door thickness Notches to cut (mm) (from the tip) The recommended tailpiece protrusion from the door is 15mm (0.6”). Notch Secure the Front Assembly using the Back Plate. To do this, place the Back Plate (ensuring the correct side placement).
- Page 13 Door Sensor Installation Adjust the position of the door sensor according to the door handling (left or right hand installation). Use the 2 x 4mm (0.16”) screws to secure the door sensor to the back plate. Right-hand Installation Left-hand Installation Please choose the suitable holes for the two screws to ensure sensor is close...
- Page 14 Fit in the Rubber Gasket Insert the front assembly cable through the rectangular hole on the rubber gasket. The hole should be on the right side of the rubber gasket. Door Sensor Cable goes through the arched hole on the Rubber Gasket Assembly Cable Right-hand Installation...
- Page 15 Connect Assembly Cable Connect the sensor cable to the Back Assembly then connect the assembly cable from the Front assembly through the 54mm (2.12”) hole to the Back Assembly. Ensure that the wire is installed properly and securely. Door Sensor Cable Assembly Set the toggle to ‘L’...
- Page 16 Secure the Back Assembly Do not overtighten the screws Screws 8mm (0.31”) Install SIM Card to the Communications Module Remove the communications module from the top of the unit. On the bottom of the communications module, you’ll see a SIM card sticker label and a SIM card slot. Insert your SIM card into the SIM card slot following the SIM card sticker label direction.
- Page 17 Insert 8 AA Alkaline Batteries and slide the battery cover downwards to close Before inserting the batteries, please ensure the ribbon is spread across the battery compartment for easier battery removal in the future. It is optional to secure the battery cover further with the additional screw. Top View of Battery Cover Tighten the screw Side View...
-
Page 18: Test Lock
Tailpiece and/or thumbturn Left-Right toggle incorrectly set incorrectly set Troubleshoot: Try Setting the Troubleshoot: Dissemble lock left-right toggle on your back and install it again. assembly to the correct side. (See Pg. 10) Still experiencing issues? Go to iglooworks.co/support for more help... -
Page 19: Prepare The Door Frame
Prepare the Door Frame Mark out where the bolt tongue locks then Ensure to align the lock to the door frame drill a corresponding hole on door frame. and mark it down. Chisel to fit the strike plate in as well. Door Frame 20mm... -
Page 20: User Guide
User Guide Lock Anatomy Front & Back Assembly Touch Screen Keypad Battery Cover Unlock LED Indicator Key hole Cover (Remove cover to access physical Thumbturn key unlock) 9V Jumpstart Clear Downlight LED... - Page 21 Features PIN / Bluetooth Unlock Master PIN Code Bluetooth Key The IoT Deadbolt unlocks with a The IoT Deadbolt unlocks with permanent Master PIN Code. Bluetooth via the app. User PIN Code The iglooworks management dashboard can generate multiple types of User Pin codes, e.g.
-
Page 22: Features
Features Security / Alarms Security Lockout Activity Logs Be assured with an additional layer Entry via PIN codes and Bluetooth Key of security with the keypad lockout if will be logged in the app. the keypad is being tampered. User can configure number of Bluetooth key access logs are updated incorrect attempts to trigger lockout. -
Page 23: Unlocking And Locking
Unlocking & Locking iglooworks App Bluetooth Unlock PIN Code Lock INB1 INB1 Last synced: a minute ago Moderate Change batteries in 9 months SYNC SYNC & UNLOCK Master PIN Lock Settings Physical Key Thumbturn Unlocking PIN Code Bluetooth Unlock Key in your PIN code and press On your app, click on the Bluetooth ‘Unlock’... -
Page 24: Lock Pairing & Provisioning
[Pair New Lock]. b) Follow the on-screen instruction to pair the lock to your account c) Select IoT Deadbolt as the lock type NEXT Connect to the IoT Network After the lock has been paired, the IoT network registration process can be initiated. -
Page 25: Lock Behaviour
Lock Behaviour Security Lockout After several incorrect PIN code attempts, the IoT Deadbolt keypad will be locked out and the security alarm will be triggered. The lock will send an alert if it has an active IoT network connection. Note: Physical key and Bluetooth Unlock can be used to unlock in this mode. -
Page 26: 9V Jumpstart
2. While holding the 9V battery to the jumpstart, key in your PIN code on the keypad followed by the ‘Unlock’ icon Please ensure terminals of the 9V battery are in contact with the Jump Start contact points of the lock for 2 seconds to activate your IoT Deadbolt. -
Page 27: Physical Keys
Physical Keys Construction and Owner Keys 1. Construction keys are brass-coloured and can be used by contractors and movers to conduct work in properties. 2. Owner keys are chrome-coloured. When they are used by the property owner for the first time, all construction keys will not work any longer to ensure security. Unlocking Orientation 1. -
Page 28: Audio And Led Indications
Audio and LED indications Actions Indications Bluetooth Connection ‘Unlock’ icon flashes Blue Connecting to Back LED blinking Blue IoT Network IoT Connection 2 quick beeps and Back LED stays Successful Blue for 5 seconds IoT Connection 1 quick beep and Back LED stays Failed Red for 5 seconds Successfully Unlocked... -
Page 29: Troubleshooting
• Use the spare QR sticker that is provided in The deadbolt is locking when it the IoT Deadbolt box. is supposed to unlock or unlock when it is supposed to lock. The lock is beeping loudly continuously and none of the functions work. - Page 30 Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 31 For enquiries go to: iglooworks.co/support...