Acer X1161 Service Manual
  1. Manuals
  2. Brands
  3. Acer Manuals
  4. Projector
  5. X1161 Series
  6. Service manual

Acer X1161 Service Manual

Hide thumbs Also See for X1161:
Table of Contents

Advertisement

Quick Links

Download this manual
SERVICE MANUAL
X1161 / X1261
Date
Revise Version
Description
2009.05.22
V1.0
Initial Issue
Copyright May, 2009
All Rights Reserved
P/N: 36.8CP01G001
SI :
TSE:
Check:
Approved:

Advertisement

Table of Contents
loading

Related Manuals for Acer X1161

Summary of Contents for Acer X1161

  • Page 1 SERVICE MANUAL X1161 / X1261 Date Revise Version Description 2009.05.22 V1.0 Initial Issue Copyright May, 2009 All Rights Reserved P/N: 36.8CP01G001 SI : TSE: Check: Approved:...
  • Page 2 Preface This manual is applied to X1161/X1261 projection system. The manual gives you a brief description of basic technical information to help in service and maintain the product. Your customers will appreciate the quick response time when you immediately identify problems that occur with our products.
  • Page 3 X1161/X1261 Comparison List Models X1161 X1261 Parts NAME LABEL 35.8CP02H001 35.8CQ03H001 DMD CHIP 48.8EH01G001 48.8CQ01G001 SPEAKER 49.8CQ01G001 IO COVER 70.8CP23GR01 70.8CQ08GR01 MAIN BOARD 70.8CP25GR01 70.8CQ09GR01 ENGINE 70.8CP22GR01 70.8CQ07GR01 X1161/X1261 Confidential...

  • Page 4: Table Of Contents

    Disassemble LVPS 2-11 Disassemble Lamp Driver Module 2-12 Disassemble Interrupt Switch 2-13 Disassemble Bottom Shielding 2-13 Disassemble Speaker (for X1261 only) 2-14 Rod Adjustment 2-14 Re-write System and Lamp Usage Hour 2-15 Assemble Speaker (for X1261 only) 2-16 X1161/X1261 Confidential...
  • Page 5 Assemble Lamp Module 2-27 Assemble Lamp Cover Module 2-27 Chapter 3 Troubleshooting LED Lighting Message Main Procedure Chapter 4 Function Test & Alignment Procedure Test Equipment Needed Service Mode OSD Reset Test Condition Test Inspection Procedure PC Mode X1161/X1261 Confidential...
  • Page 6 Optical Performance Measure 4-11 Others 4-12 Chapter 5 Firmware Upgrade Equipment Needed DLP Composer Lite Setup Procedure USB Driver Upgrade Procedure (for X1161 only) Firmware Upgrade Procedure Waveform Download Chapter 6 EDID Upgrade EDID Introduction Equipment Needed Setup Procedure (VGA)

  • Page 7: Chapter 1 Introduction

    (��inimum; projection lens at tele mode) • �7����: � Full White �ith �ull po�er �� �ull Black �ith eco po�er (Typical; projection lens at tele mode) ●� ��arketing spec: • ��5����: � (�or X����) • ��������: � (�or X����) X1161/X1261 Confidential...
  • Page 8 ●� ������� ~ 7�5�� rpm �� CW �X and ��5X (5�� ~��5Hz) �� �amp ●� ����� Watt �S�A�� ������� open type �amp ●� Standards : • ��TSC (���5���������) ��� Video compati�ility • PA� (B��D��G��H��I��������) • S�CA�� (B��D��G��K��K����) • HDTV (�����i��57�i �����p�� 57�p�� 7���p�� �������i�� �������p) Confidential X1161/X1261...
  • Page 9 • �or �5���� - 5������ �t�� 5 - ���� °C • �or 5������ - ��������� �t�� 5 - �5 °C ●� Storage: -���°C ~ ���°C ●� �perating: 5°C ~ ��5°C�� �������H (��ax�)�� ��on-condensing �� ��aximum Humidity ●� Storage: -���°C ~ ���°C�� �������H (��ax�)�� ��on-condensing Confidential X1161/X1261...

  • Page 10: Compatible Mode

    ��� ������ QuadVGA ������ x ���� 75�� SXGA� ������ x ���5�� ��� �5��� UXGA ������ x ������ ��� 75����� Po�er ��ac G� ���� x ����� ����(�7) ����� ������ x ����� ��� ��7�� ����� x 7��� ��� ����� Confidential X1161/X1261 �-�...
  • Page 11 ��� 5��� WSXGA� ������ x ���5�� ��� �5��� Horizontal scan rate ����k-�����kHz Vertical scan rate 5��-��5Hz ��ax� pixel rate �7����Hz Note: If the Compatibility modes supportive signal is different from User's Manual, please refer to User’s Manual. Confidential X1161/X1261 �-5...

  • Page 12: Product Overview

    1-3 Product Overview Projector Outlook Front /Upper side Item Description Item Description Ventilation (inlet) �ens cap Ventilation (outlet) Po�er �utton �emote control recei�ers �� �emote control � Focus ring � �oom le�er �oom lens ��� Horn Confidential X1161/X1261...
  • Page 13 ��onitor loop-through output � S-Video input connector �� connector (VGA-�ut) Composite �ideo input connector � Audio input connector Below items are for X1161 only: ���� USB connector ��� USB connector 7� �S���� connector Note: “*” for optional connector port. Confidential...
  • Page 14 Remote Control and Control Panel Layout Confidential X1161/X1261 �-��...
  • Page 15 �ooms the projector display in or out� S�U�C� Changes the acti�e source� ��omentarily turns o�� the �ideo� Press “HID�� to HID� hide the image�� press again to display the image� �mpo�ering Uni�ue Acer �unctions: eVie��� eTimer�� ePo�er ��anagement� Note: Confidential X1161/X1261 �-�...
  • Page 16 Composite �ideo ca�le �� Audio ca�le jack���CA � �S���� ca�le � USB ca�le Note: To ensure the projector works well with your computer, please make sure the timing of the display mode is compatible with the projector. Confidential X1161/X1261 �-���...
  • Page 17 System Block Diagram (for X1161) Confidential X1161/X1261 1-11...
  • Page 18 System Block Diagram (for X1261) Confidential X1161/X1261 1-12...
  • Page 19 Bottom Cover Dimension Confidential X1161/X1261 1-13...

  • Page 20: Equipment Needed & Product Overview

    * Note: - If you need to replace the Main Board, you have to get into Service Mode and record the lamp usage hour. please refer to section 2-21. - As the process of X1161 disassembling is the same as X1261, we take X1261 for example here.

  • Page 21: Disassemble Lamp Cover Module

    1. Loosen 2 screws (as red circle) on the Lamp Cover. 2. Disassemble the Lamp Cover Module. 2-3 Disassemble Lamp Module 1. Loosen 2 screws (as red circle) on the Lamp Module. 2. Take off the Lamp Module. X1161/X1261 Confidential...

  • Page 22: Disassemble Top Cover Module

    2. Remove the Top Cover Module. Note: - When you remove the Top Cover, take care the 6 tenons (as green square). 2-5 Disassemble Top Shielding 1. Unscrew 5 screws (as red circle) to disassemble the Top Shielding. X1161/X1261 Confidential...

  • Page 23: Disassemble Front Cover And Ir Sensor Board

    2 tenons (as green square). 3. Remove the Front Cover. 4. Tear off the mylar (as blue square). 5. Unscrew 2 screws (as red circle). 6. Remove the IR Sensor Board and IR Cap. IR Cap IR Sensor Board X1161/X1261 Confidential...

  • Page 24: Disassemble Main Board Module And Io Cover Module

    Please refer to the below table details of each connector on Main Board. Male Connector Item The key feature Figure on Main Board Lamp Driver Black wire tube (5 pin) Compose of Red/Yellow/Black System Fan Wire (3 pin) Compose of Red/Black/White Blower Wire (3 pin) X1161/X1261 Confidential...
  • Page 25 Wire and Black wire tube (3 pin) Speaker Compose of Red/Black Wire and (for X1261 only) Black wire tube (2 pin) 4. Unplug 1 connector (as blue square). 5. Disassemble the Main Board Moudle. 6. Unscrew 2 screws (as green circle). X1161/X1261 Confidential...

  • Page 26: Disassemble Engine Module

    7. Unscrew 4 hex screws (as blue circle). 8. Separate the Main Board and IO Cover Module. IO Cover 2-8 Disassemble Engine Module 1. Tear off EMI Gasket (as green square). 2. Unscrew 4 screws (as yellow circle) to disassemble the Engine Module. X1161/X1261 Confidential...

  • Page 27: Disassemble Color Wheel Module

    2. Rotate the screw (as yellow circle) 180° counterclockwise to disassemble the DMD Board and DMD Chip. Note: - Avoid touching the DMD Chip when you disassemble it. - Pay attention to the fixed position when assembling the DMD Chip. X1161/X1261 Confidential...

  • Page 28: Disassemble Zoom Ring

    1. Unscrew 2 screws (as red circle) to disassemble the Zoom Ring and Zoom Ring Fixed Holder. Zoom Ring Zoom Ring Fixed Holder 2-12 Disassemble Focus Ring 1. Unscrew 3 screws (as red circle) to disassemble the Focus Ring. Focus Ring X1161/X1261 Confidential...

  • Page 29: Disassemble System Fan Module

    3. Disassemble the System Fan Module. 4. Unscrew 4 screws (as blue circle) to separate System Fan and Fan Shielding. Note: - Take the Fan Module as the right gesture. System Fan Fan Shielding the wrong gesture the right gesture X1161/X1261 Confidential 2-10...

  • Page 30: Disassemble Blower

    2-15 Disassemble LVPS Module 1. Unplug 2 connectors (as yellow square). 2. Unscrew 6 screws (as red circle). 3. Disassemble the LVPS Module and the AC Inlet Bracket. 4. Unplug 1 connector (as green square). AC Inlet Bracket X1161/X1261 Confidential 2-11...

  • Page 31: Disassemble Lamp Driver Module

    3. Unplug 3 connectors (as green square) to disassemble the cables from Lamp Driver Module. 4. Unscrew 4 screws (as yellow circle) to disassemble the Lamp Driver Module and Lamp Driver Holder. Lamp Driver to Lamp Cable Lamp Driver Holder X1161/X1261 Confidential 2-12...

  • Page 32: Disassemble Interrupt Switch

    1. Unfasten 2 tenons (as green square) to disassemble the Interrupt Switch. Interrupt Switch 2-18 Disassemble Bottom Shielding 1. Tear off the EMI tapes (as yellow square). 1. Unscrew 2 screws (as red cricle) to disassemble the Bottom Shielding. X1161/X1261 Confidential 2-1...

  • Page 33: Rod Adjustment

    - Change the screen to "white screen". - Adjust the screws by using the rod on the engine module to readjust the image. ("Screw 1" should be adjusted first, and then "screw 2". Adjust until the yellowish or bluish parts disappeared.) X1161/X1261 Confidential 2-1...

  • Page 34: Re-Write System And Lamp Usage Hour

    2. Get into Other Settings Mode - Use "Up" or "Down" buttons to select "Other Settings", then press "Menu" button. 3. Re-write System Hours - Select "System Hours Adjust" and use "Left" or "Right" buttons to re-write the "System Hours (full)". X1161/X1261 Confidential 2-15...

  • Page 35: Assemble Speaker (For X1261 Only)

    Service Mode. Note: left key = decrease System/Lamp hour right key =increase System/Lamp hour 2-22 Assemble Speaker (for X1261 only� only� � 1. Fasten 2 tenons (as green square) as blue arrows point to assemble the Speaker. X1161/X1261 Confidential 2-16...

  • Page 36: Assemble Bottom Shielding

    Shielding 1. Screw 2 screws (as red circle) to assemble the Bottom Shielding. 2. Stick the EMI tapes (as yellow square). 2-24 Assemble Interrupt Switch 1. Fasten 2 tenons (as green square) to assemble the Interrupt Switch. X1161/X1261 Confidential 2-17...

  • Page 37: Assemble Lamp Driver Module

    Lamp Driver Holder. 2. Plug 3 connectors (as green square) to assemble the cables on Lamp Driver Module. 3. Screw 2 screws (as blue circle). 4. Screw 1 screw (as red circle) to assemble the Lamp Driver Module. X1161/X1261 Confidential 2-1...

  • Page 38: Assemble Lvps Module

    2. Assemble the LVPS Module and the AC Inlet Bracket. 3. Screw 6 screws (as red circle). 4. Plug 2 connectors (as yellow square). 2-27 Assemble Blower 1. Assemble the Blower. 2. Screw 3 screws (as red circle). X1161/X1261 Confidential 2-1...

  • Page 39: Assemble System Fan Module

    1. Screw 4 screws (as blue circle) to assemble System Fan and Fan Shielding. 2. Assemble the System Fan Module. 3. Stick the EMI tape (as green square). 4. Screw 3 screws (as red circle) to assemble the Fan Module. X1161/X1261 Confidential 2-20...

  • Page 40: Assemble Focus Ring

    2-29 Assemble Focus Ring 1. Screw 3 screws (as red circle) to assemble the Focus Ring. 2-30 Assemble Zoom Ring 1. Screw 2 screws (as red circle) to assemble the Zoom Ring and Zoom Ring Fixed Holder. X1161/X1261 Confidential 2-21...

  • Page 41: Assemble Dmd Chip And Dmd Board

    2-32 Assemble Color Wheel Module 1. Screw 1 screw (as blue circle) to assemble the Photo Sensor Board on the Color Wheel Module. 2. Screw 2 screws (as red circle) to assemble the Color Wheel Module on Engine Module. X1161/X1261 Confidential 2-22...

  • Page 42: Assemble Engine Module

    Engine Module. 2. Stick the EMI Gasket (as green square). 2-34 Assemble IO Cover and Main Board Module 1. Assemble the IO Cover and Main Board Module. 2. Screw 4 hex screws (as blue circle). X1161/X1261 Confidential 2-2...
  • Page 43 4. Assemble the Main Board Module. 5. Plug 1 connector (as blue square). 6. Screw 2 screws (as red circle). 7. Plug 6 connectors (as yellow square). 8. Stick 3M tape (as green square) on the Main Boad Module. X1161/X1261 Confidential 2-2...

  • Page 44: Assemble Ir Sensor Board And

    2. Screw 2 screws (as red circle). 3. Stick the mylar (as blue square). 4. Assemble the Front Cover. 5. Press two sides (as red arrows point) to fasten 2 tenons (as green circle). 6. Plug 1 connector (as yellow square). X1161/X1261 Confidential 2-25...

  • Page 45: Assemble Top Shielding

    2-37 Assemble Top Cover Moudle 1. Assemble the Top Cover Module. Note: Take care the 6 tenons (as green square) when you assemble the Top Cover. 2. Screw 2 screws (as red circle) on the Bottom Cover. X1161/X1261 Confidential 2-26...

  • Page 46: Assemble Lamp Module

    1. Assemble the Lamp Module. 2. Tighten 2 screws (as red circle) on the Lamp Module. 2-39 Assemble Lamp Cover Module 1. Assemble the Lamp Cover Module. 2. Tighten 2 screws (as red circle) on the Lamp Cover. X1161/X1261 Confidential 2-27...

  • Page 47: Led Lighting Message

    0.5 second H(On), 0.5 second L(Off) flashing blue twice, and red down) LED ON 2 second, and by returns Error (Color Wheel 0.5 second H(On), 0.5 second L(Off) flashing blue twice, and red Failure) LED ON 2 second, and by returns Note: Steady Light: "V" No Light: "--" X1161/X1261 Confidential...

  • Page 48: Main Procedure

    - Ensure all connectors are securely connected and aren’t broken - Check Lamp Cover, Interrupt Switch - Check Lamp Module - Check Lamp Driver No Light On - Check LVPS - Check Main Board - Check Color Wheel - Check Photo Sensor Board X1161/X1261 Confidential...
  • Page 49 - Check DMD Board - Check Main Board " " - Do Reset (All data) of the OSD Menu - Adjust Color Wheel Index Color Abnormal - Check Main Board - Check DMD Board - Check Color Wheel X1161/X1261 Confidential...
  • Page 50 - Check Main Board - Ensure that the signal cables and source are work as well - Ensure that your Projector is not in “Mute” mode Audio Abnormal (for X1261 only) - Check Main Board - Check Speaker X1161/X1261 Confidential...
  • Page 51 Un-lock SNID and Default Language Reset (refer Failure to 6-5 of Chapter 6) c. Press "Power", "Left", "Left" and "Menu" buttons sequentially on remote controller to get into Service Mode to obtain the SNID number, then calculate the Universal Password. X1161/X1261 Confidential...

  • Page 52: Function Test & Alignment Procedure

    1. After final QC step, we have to erase all saved change again and restore the OSD default setting. The following actions will allow you to erase all end-users' settings and restore the default setting: (1) Please get into OSD menu. (2) To execute "Reset" function. X1161/X1261 Confidential...

  • Page 53: Test Condition

    Screen Defects (While replacing DMD Chip, DMD Board, Main Board) 12.5 cm Frame Zone C Zone B 12.5 cm < Figure: Zone A, Zone B, Zone C & Frame (as green line) Definition, Active area=Zone A + Zone B > X1161/X1261 Confidential...

  • Page 54: Test Inspection Procedure

    EDID Re-write Lamp Hour Usage Reset Default Language Rod adjustment Waveform Download Note: - If Color appears abnormal after changing Main Board Module, please do Color Wheel index adjustment. - After changing parts, check the information above table. X1161/X1261 Confidential...

  • Page 55: Pc Mode

    Note: - When getting into function test, adjust the zoom ring and focus ring to guarantee the image maximum and clearest, then start to test. - Test signal: analog 800 x 600 @60Hz (for X1161); analog 1024 x 768 @60Hz (for X1261).
  • Page 56 Note: The defect criteria follows TI specification. 4. Dead Pixel (Dark pixel) Procedure - Test equipment: video generator - Test signal: analog 1024 x 768 @60Hz - Test pattern: Full white Inspection item - Dead pixels check. Full white X1161/X1261 Confidential...
  • Page 57 - The dark blemish is unacceptable when it is more Blue 60 than four under blue 60 pattern. - Ref. Defect specification table Note: The defect criteria follows TI specification. 7. Focus test Procedure - Test equipment: video generator X1161/X1261 Confidential...
  • Page 58 SMPTEbar - If color appears abnormal, please get into service mode to do Color Wheel Index adjustment. - The PC mode functionally sure be workable include support format with frequency and auto detected functional will be workable. X1161/X1261 Confidential...

  • Page 59: Calibration

    ", "Left", "Left" and "Menu" , "Left", "Left" and "Menu" "Left", "Left" and "Menu" Left", "Left" and "Menu" ", "Left" and "Menu" , "Left" and "Menu" "Left" and "Menu" Left" and "Menu" " and "Menu" and "Menu" "Menu" Menu" " X1161/X1261 Confidential...
  • Page 60 - Note (1) Calibration pattern should be in full screen mode. (2) Please press "Power", "Left", "Left" and "Menu" buttons sequentially to get into Service Mode. (3) Choose and access "G Sensor Calibration" for correction in Service Mode. X1161/X1261 Confidential...

  • Page 61: Video Performance

    - Test signal: CVBS Inspection item - Audio performance test Inspection Distance - 1.8 M ~2.5 M Criteria - Check the sound from speaker - Plug Audio cable into Audio In port, check if "Volume" is normal. X1161/X1261 Confidential 4-10...

  • Page 62: Optical Performance Measure

    "Contrast" is "70", and the "Format" is "4:3". 2. Brightness Procedure - Full white pattern - Use CL100 to measure brightness values of P1~P9. - Follow the brightness formula to calculate brightness values. ☼ Brightness Formula Avg. (P1~P9)*1.1m Criteria ● 1100 ANSI lumen X1161/X1261 Confidential 4-11...

  • Page 63: Others

    ☼ Contrast Formula P5/B5 Full white pattern Note: P5=center of white image B5 = the center of black image. Criteria ● 2500: 1 (for X1161) ● 2100: 1 (for X1261) Full black pattern 4. Uniformity Procedure - Full white pattern - Use CL100 to measure brightness values of P1~P9 (see image: full white).
  • Page 64 It should be locked in the correct place. Plastic Parts All plastic parts can not be broken and damaged. Safety or warning All safety and warning labels should be visible, label including all contents. All interface connectors should be complete and Connector workable. X1161/X1261 Confidential 4-13...

  • Page 65: Firmware Upgrade

    5-1 Equipment Needed Software: (DDP 2430) - DLP Composer Lite 7.1 - Firmware (*.img) - Library file (X1161 X1261 FlashDeviceParameters) (library file has to put in PC and set right path in 5-4 step 4) Hardware: - Projector - Power cord: 42.50115G001 - RS232 cable: 42.83618G001 (for X1261)

  • Page 66: Dlp Composer Lite Setup Procedure

    1. Choose "DLP Composer Lite V7.1 Setup" Program. 2. Click "Next". 3. Read "License Agreement". - Choose "I accept and agree to be bound by all the terms and conditions of this License Agreement". - Click "Next". 4. Click "Next". X1161/X1261 Confidential...
  • Page 67 5. Click "Next". 6. Click "Next". 7. The program is executing "installing" status. 8. Click "Finish". X1161/X1261 Confidential...

  • Page 68: Usb Driver Upgrade Procedure (For X1161 Only)

    5-3 USB Driver Upgrade Procedure (for X1161 only) 1. Set up - Plug in Power Cord to the projector. - Connect PC and projector by USB Cable. 2. Execute Program - Open the "DLP Composer Lite 7.1" folder. - Select and double click "usbupdate.cmd".

  • Page 69: Firmware Upgrade Procedure

    2. Execute the "DLP Composer Lite 7.1" file. 3. Click "Edit" and "Perferences". 4. Click "Library". - Click "Browse" and navigate to the directory where you put the DLP Composer installation files in. - Click "X1161 X1261 FlashDeviceParameters" folder. - Click "OK". X1161/X1261 Confidential...
  • Page 70 5. Click "Communications". - Select "Serial Port". (for X1261) - Select "USB". (for X1161) for X1261 - Select the COM port which you are using. for X1261 - Click "Configure". 6. For X1261: "Serial Port Configuration" picture will appear on the screen.
  • Page 71 - Unplug RS232 cable and power cord. (for X1261) Note: Please unplug USB cable and power cord. (for X1161) 12. Check FW version. - Re-plug in power cable, then restart the unit and get into the Service Mode to check the firmware version.

  • Page 72: Waveform Download

    - Hold on "power" button and plug in the power cord. - After 2 seconds, the power LED will flash blue, then loosen "power" button. - After 5 seconds, the projector will automatically get into standby status. - Waveform Download is completed. X1161/X1261 Confidential...

  • Page 73: Edid Upgrade

    Display Data Channel (DDC), which sites between the display device and the PC graphics adapter. The system uses this information for configuration purposes, so the monitor and system can work together. Note: - The EDID Upgrade procedure for X1161 is the same as X1261, we take X1261 for here. X1161/X1261...

  • Page 74: Equipment Needed

    - Power Cord for Projector (42.53506G002) - VGA Cable (42.87305G102) - RS-232 9 Pin Cable (pin to pin, F-M) (42.83C07G001) - Generic Fixture (80.00001.001) for EDID Key-in (Fixture: JP3 must be closed) - Power Adapter (47.57803G001) - Monitor - PC X1161/X1261 Confidential...

  • Page 75: Setup Procedure (Vga)

    (2) Connect P3 of fixture with VGA Port of projector by VGA Cable. Adapter RS232 Cable (3) Plug Power Adapter to JP1 of fixture. (4) Plug Power Cord to projector. Note: You must confirm that the JP3 is closed. Power Port VGA Port X1161/X1261 Confidential...

  • Page 76: Edid Key-In Procedure

    (1) Select the COM Port which you are using. (2) Click "Model". (3) Select the source file (*.ini). (4) Click "Open". (5) Key in the Serial Number into the Barcode blank space. (6) In "Write Source Select" item, select "Analog". (7) Click "Program". X1161/X1261 Confidential...
  • Page 77 4. When the EDID program is completed, a message "OK" will appear on the screen. 5. Read EDID "Analog" information - In "Read item", select "Analog" and "Trans", then click the "Read" button. 6. EDID informations will show the result. X1161/X1261 Confidential...

  • Page 78: Un-Lock Snid And Default Language Reset

    Note: If it is fail, please do the actions as above steps item (1)-(2) S/N General rule: Use the last 1 digit code (as red word) for language information Language Code (F) Default Language English Thailand Japan Russian Germany Hungarian X1161/X1261 Confidential...
  • Page 79 Appendix A (Exploded Image) Note: This chapter is only designed to show the exploded image of the projector. For updated part numbers, please refer to RSPL report. D.C. X1161 X1161/X1261 Confidential...
  • Page 80 70.8CP03G001 FRONT MODULE X1161 SP.8CP01GC01 LAMP MODULE FOR PROJECTOR X1161 70.8CP06G001 LAMP MODULE X1161 70.8CP24GR01 ASSY LAMP COVER MODULE X1161 (SERVICE) 51.8CP03H001 LAMP COVER LN2520 X1161 61.8CP13G001 LAMP COVER AL FOL X1161 LOCK SCREW PAN MECH M3*8.5-3.5 BLACK 61.00018G003 (1018+HEAT TREATMENT) 61.8CP07G001...
  • Page 81 D.C. X1261 X1161/X1261 Confidential...
  • Page 82 70.8CP03G001 FRONT MODULE X1161 SP.8CP01GC01 LAMP MODULE FOR PROJECTOR X1161 70.8CP06G001 LAMP MODULE X1161 70.8CP24GR01 ASSY LAMP COVER MODULE X1161 (SERVICE) 51.8CP03H001 LAMP COVER LN2520 X1161 61.8CP13G001 LAMP COVER AL FOL X1161 LOCK SCREW PAN MECH M3*8.5-3.5 BLACK 61.00018G003 (1018+HEAT TREATMENT) 61.8CP07G001...
  • Page 83 I.D. X1161 X1161/X1261 Confidential...
  • Page 84 Item Description Parts Supply ASSY BOTTOM COVER MODULE X1161 70.8CP26GR01 (SERVICE) 51.8CP02H001 BOTTOM COVER MN3600H X1161 52.88N07G001 ADJUSTABLE FOOT RUBBER,EP721 86.0A123G024 HEX NUT M3*5.5*0.5P L2.4 Ni 61.8CP06G001 BOTTOM SHIELDING SECC (for X1161) 70.8CP05G001 BOTTOM SHIELDING MODULE (for X1261) 51.8CP12G001 MYLAR LVPS X1161 70.8CP14G001...
  • Page 85 Front Module Description Parts Supply Item 51.88T24G001 FRONT R CAP FOR X1160E 80.8CP05G001 PCBA IR SENSOR BD FOR X1161 51.8CP09H001 FRONT COVER MN3600H X1161 85.3A122G040 SCREW CAP MECH M2*4 Ni 61.8CP14H001 ACER LOGO FOR X1161 52.8CP09G001 SPONGE LIGHTCUT FR-CW X1161...
  • Page 86 IO MODULE X1161 X1161/X1261 Confidential V...
  • Page 87 Description Parts Supply Item 61.8CP10G001 MAIN SHIELDING SMALL TINPLATE X1161 70.8CP25GR01 ASSY MAIN BOARD MODULE X1161 (SERVICE) 80.8CP01G001 PCBA MAN BOARD FOR X1161 35.8CP01H001 LABEL O X1161 51.8CP13G001 MYLAR MAIN-BD TO LVPS X1161 51.8CP16G001 MYLAR MAIN-BD SMALL X1161 51.8CP11H001 IO COVER MN3600H X1161 52.8CP10G001...
  • Page 88 IO MODULE X1261 X1161/X1261 Confidential...
  • Page 89 70.8CQ09GR01 ASSY MAIN BOARD MODULE X1261 (SERVICE) 80.8CQ01G001 PCBA MAN BOARD FOR X1261 35.8CQ02H001 LABEL IO BASE X1261 51.8CP13G001 MYLAR MAIN-BD TO LVPS X1161 51.8CP14G001 MYLAR MAIN-BD X1161 70.8CQ08GR01 ASSY IO COVER MODULE X1261 (SERVICE) 51.8CQ01H001 IO COVER MN3600H X1261 52.8CQ01G001...
  • Page 90 Bottom Shielding Module Description Parts Supply Item 61.8CP06G001 BOTTOM SHIELDING SECC X1161 61.8CP08G001 SPEAKER BRKT SUS301 X1161 49.8CQ01G001 SPEAKER 2W 16OHM DAB128 90mm X1261 52.8CP05G001 SPONGE SPEAKER X1161 X1161/X1261 Confidential...
  • Page 91 One- Fan Module X1161/X1261 Confidential X...
  • Page 92 FAN SHELDING FRONT AIR TIGHT CVS X1160 52.88T08G001 FAN SHELDING AIR TIGHT F12 X1160 52.89T01G001 BLOWER AIR TIGHT F12 H5350 51.81540G001 TAPE 3M J350 17*60mm SUNON 45*20mm GB1245PKV1-8AY, F TYPE 49.8CS01G001 BLOWER FAN 52.82G08G001 BLOWER 4520 RUBBER EP7190 X1161/X1261 Confidential...
  • Page 93 Parts Supply ASSY OPTICAL ENGINE MODULE Z15 (S450) 70.8CP09G001 (for X1161) 70.8CQ02G001 ASSY OPTICAL ENGINE MODULE (for X1261) 51.8CP04H001 FOCUS RING MN3600H X1161 51.8CP08H001 ZOOM RING MN3600H X1161 51.89Z04G001 ZOOM RING FIXED HOLDER EX330 85.1A326G060 SCREW PAN HEAD MECH M2.6*6 BLACK 85.WA321G040...
  • Page 94 Assy Engine Module X1161/X1261 Confidential...
  • Page 95 YO YM39 PROJECTION LENS 1.1X ZOOM 70.8CP15G001 ASSY RELAY MODULE Z15 23.8AH20G001 CONDENSER1 FOR A15W 70.8CP22GR01 ASSY ENGINE MODULE X1161 (SERVICE) 70.8CQ07GR01 ASSY ENGINE MODULE X1261 (SERVICE) 85.1A526G060 SCREW PAN MECH M2.6*6 Ni NYLOK 80.8CP02G001 PCBA DMD BOARD FOR X1161 70.8CP13G001...
  • Page 96 Assy Color Wheel Module Z15 Item Description Parts Supply 61.8CP03G001 CW BRACKET SECC X1161 80.8CP04G001 PCBA PHOTO SENSOR BOARD FOR X1161 23.8EF19G001 YO 6S R81Y41G84C31W52B71_HE3 CW 85.1A126G040 SCREW PAN MECH M2.6*4 Ni TAPE 3M J350 10*5mm FOR COLOR WHEEL 51.82Y29G001 DP715 70.8CP21GR01...
  • Page 97 CABLE W.A. 2P #22 100mm LAMP DRIVER TO 42.00436G002 LAMP X1160 52.88T02G001 LAMP DRIVER HOLDER AIR TIGHT F12 X1160 52.88T03G001 LAMP DRIVER HOLDER AIR TIGHT-FR F12 X1160 51.88T18G001 KAPTON 10*10 0.05t X1160 52.86K01G001 LAMP SPONGE F12 35X5X3.2mm EP709 X1161/X1261 Confidential...
  • Page 98 A.K. X1161/X1261 Confidential...
  • Page 99 SERVICE STATION CARD PE BAG ZIPPER #9 W/RECYCLING MARK FOR 51.86213G002 OPTOMA 36.8CP02G001 QUICK START CARD MULTILINGUAL 35.82001G111 AK LABEL 3”*3” BLANK USER’S GUIDE MULTILINGUAL (CD) ACER X1161/ 36.8CP01H001 X1261 NFRARED REMOTE CONTROLLER X1161 X3 45.8CP01G001 “BONTECH” 36.00029G001 SECURITY CARD FOR ACER 56.8CP01G001...

  • Page 100: Serial Number System Definition

    00000 = Serial Numbers 59 = Manufacturing Code 0 = Version Code 1 = Auto-Language Code EX: EYK0201001915000005901 This label represents the serial number for X1261. It is produced at CPC on fifteenth week of 2009. Its serial code is 00000. X1161/X1261 Confidential...

  • Page 101: Pcba Code Definition

    II. PCBA Code Definition PCBA Code for Projector XXXXXXXXX EEEE Vendor Code Firmware Version MB version Date Code X1161/X1261 Confidential...
  • Page 102 * 0 IR 030\r Hide * 0 IR 031\r Source * 0 IR 032\r Video: Color saturation adjustment * 0 IR 033\r Video: Hue adjustment * 0 IR 034\r Video: Sharpness adjustment * 0 IR 035\r Query Model name X1161/X1261 Confidential...
  • Page 103 * 0 IR 042\r Keystone Up * 0 IR 043\r Keystone Down * 0 IR 046\r Zoom * 0 IR 047\r e-Key * 0 IR 048\r Color RGB * 0 IR 049\r Language Note: The command with end "\r" means "Enter". X1161/X1261 Confidential...

This manual is also suitable for:

X1261

Table of Contents