Husqvarna 525PT5S Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Trimmer
  5. 525PT5S
  6. Operator's manual

Husqvarna 525PT5S Operator's Manual

Hide thumbs Also See for 525PT5S:
Table of Contents

Advertisement

Quick Links

Download this manual
525PT5S
EN
Operator's manual
2-28

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna 525PT5S

Summary of Contents for Husqvarna 525PT5S

  • Page 1 525PT5S Operator's manual 2-28...

  • Page 2: Table Of Contents

    Contents Introduction..............2 Troubleshooting............23 Safety................4 Transportation, storage and disposal......24 Assembly..............10 Technical data.............. 24 Operation..............11 Accessories..............25 Maintenance..............15 Declaration of Conformity..........27 Introduction Intended use Only use the product with accessories that are approved Accessories on page 25 . by the manufacturer.
  • Page 3 13. Throttle trigger lockout 14. Spark plug cap and spark plug Fuel. 15. Cylinder cover 16. Starter handle 17. Impact guard 18. Fuel tank 19. Air filter cover Chain oil. 20. Air purge 21. Choke control 22. Throttle trigger Adjustment of the oil flow. 23.

  • Page 4: Safety

    This product is not electrically insulated. If the product touches or comes close to high-volt- age power lines it could lead to death or serious injury. Electricity can jump from one point to another by arcing. The higher the voltage, the greater the distance electricity can jump. Electricity can also travel through branches and other objects, especially if they are wet.
  • Page 5 particles that nay be carcinogenic. Avoid being • Never use the machine indoors or in spaces lacking exposed to these compounds when handling the proper ventilation. Exhaust fumes contain carbon muffler and /or spark arrester. Prior to any handling monoxide, an odourless, poisonous and highly of the muffler and/or the spark arrester, refer to dangerous gas.
  • Page 6 • If the safety devices are defective, speak to your occur. Let your dealer help you select the right Husqvarna servicing dealer. equipment. • Use a protective helmet where there is a risk of To do a check of the throttle trigger lockout falling objects.
  • Page 7 1. Push the throttle trigger lockout (A) and make sure 6. Release the throttle control and make sure that the that the throttle control is released (B). When you cutting attachment stops. If the cutting attachment release the handle, the throttle control and the rotates with the throttle in the idle position, do throttle trigger lockout move back to their initial a check of the carburetor adjustments.
  • Page 8 To do a check of the muffler let the product dry. Remove unwanted fuel from the product. • If you spill fuel on your clothing, change clothing immediately. • Do not get fuel on your body, it can cause injury. If you get fuel on your body, use a soap and water to remove the fuel.
  • Page 9 • Regularly do the safety checks, maintenance and • Make sure that the saw chain has the correct service instructions given in this manual. Regular tension. If the saw chain is not tight against the guide maintenance increases the life of the product bar, the saw chain can derail.

  • Page 10: Assembly

    Assembly To assemble the impact guard 2. Fit the bar over the bar bolt. Place the bar in its rearmost position. Place the chain over the drive 1. Assemble the guard with 3 screws. sprocket and in the groove on the bar. Begin on the top side of the bar.

  • Page 11: Operation

    To adjust the harness 6. The chain is correctly tensioned when it does not sag from the underside of the bar, but can still be Always use the harness when you operate the product. turned easily by hand. Hold up the bar tip and tighten The harness gives maximum control during operation of the bar nuts with the combination spanner.
  • Page 12 1. Clean the area around the fuel tank cap. • If Husqvarna two-stroke oil is not available, use a 2. Shake the container and make sure that the fuel is two-stroke oil of good quality for air-cooled engines.
  • Page 13 23 . better control over where they fall. • Use Husqvarna chain oil for maximum saw chain life and to minimise environmental damage. If Husqvarna chain oil is not available, we recommend you to use a standard chain oil.
  • Page 14 To prepare the product for start • Never cut through the swelling at the root of the branch as this will slow down healing and increase 1. Push the air purge bulb 10 times. the risk of fungal attack! • Use the stop at the base of the cutting head to provide support during cutting.

  • Page 15: Maintenance

    CAUTION: To stop the product Do not pull the starter rope all the way out and do not let go off 1. Move the stop switch into the stop position to stop the starter rope handle when the starter the engine. rope is fully extended.
  • Page 16 Maintenance Daily Weekly Monthly Clean the external surface. Make sure that the throttle trigger lock and the throttle works correctly. Do a check of the stop switch to make sure that it works correctly. Make sure that the saw chain does not rotate at idle speed. Clean the air filter.
  • Page 17 3. Adjust the idle speed with the idle adjustment screw 3. Remove the screw holding the spark arrestor mesh. T which is identified with "T" mark. Turn the idle adjustment screw clockwise until the saw chain starts to turn. 4. Clean the spark arrestor mesh if it is blocked or replace it if it is damaged.
  • Page 18 To clean the air filter CAUTION: An air filter that is damaged, very dirty, or soaked with fuel must always be replaced. Clean the air filter from dirt and dust regularly. This prevents carburetor malfunctions, starting problems, loss of engine power, wear to engine parts and more fuel consumption than usual.
  • Page 19 To check the chain drive sprocket 3. Clean the groove in the guide bar. 1. Regularly check the degree of wear on the drive sprocket. Replace if wear is excessive. 4. Examine the groove in the guide bar for wear. Replace the guide bar if it is necessary.
  • Page 20 Chain oil hole and hole for chain tensioner. The the guide bar and saw chain combination recommended guide bar must align with product. by Husqvarna. This is necessary to keep the safety Accessories on functions of the product. Refer to page 25 , for a list of replacement bar and chain combinations that we recommend.
  • Page 21 It is not easy to sharpen a saw chain correctly without performance you must remove filing material from the the correct equipment. Use Husqvarna file gauge. This depth gauge (B) to receive the recommended depth will help you to keep maximum cutting performance.
  • Page 22 1. Use a flat file and a depth gauge tool to adjust 5. Tighten the bar nuts using the wrench and lift the the depth gauge setting. Only use Husqvarna depth front of the guide bar at the same time.

  • Page 23: Troubleshooting

    2. If the saw chain lubrication does not operate • Turn the adjuster screw clockwise to increase the oil To do correctly, do a check of the guide bar. Refer to flow. a check of the guide bar on page 19 for instructions. Speak to your servicing dealer if the maintenance steps does not help.

  • Page 24: Transportation, Storage And Disposal

    5. Do a complete servicing of the product. • Remove the spark plug cap from the spark plug. • Attach the product safely during transportation. Technical data Technical data 525PT5S Engine Cylinder displacement, cm 25.4 Cylinder bore, mm Stroke, mm Recommended max. speed, rpm...

  • Page 25: Accessories

    The part numbers are given in the table below. Using Husqvarna file gauge will give you the correct If you do not know which saw chain you have on your filing angles. We recommend you to always use a product, turn to your servicing dealer.
  • Page 26 0.025 in / 5/32 in / 4.0 mm 85° 30° 580 68 74-01 0.65 mm 712 - 008 - 25.10.2022...

  • Page 27: Declaration Of Conformity

    Declaration of Conformity EU Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Pole saw Brand Husqvarna Type / Model 525PT5S Identification Serial numbers dating from 2022 and onwards...
  • Page 28 UK Declaration of conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Pole saw Brand Husqvarna Type / Model 525PT5S Identification Serial numbers dating from 2022 and onwards complies fully with the following UK regulations:...
  • Page 29 712 - 008 - 25.10.2022...
  • Page 30 712 - 008 - 25.10.2022...
  • Page 31 712 - 008 - 25.10.2022...
  • Page 32 Original instructions 1143381-26 2022-11-04...

Table of Contents