Step 4. Allow branches to fall into place or gently pull branches up and
out. When adjusting branches be sure that all wires are free of
branch hinges. (See Fig. 4)
Step 5. Shape the branches. Starting with tips closest to the pole,
shape one tip to the right, one to the left and one at the center
of the main stem. Repeat pattern for each branch. (See Fig. 5)
Step 6. Plug the well-connected power cord from the tree section (C)
into a proper outlet. Please note this tree comes with a foot
pedal switch and remote control for easy illumination and
changing functions. This tree is Color Changing, the 8 lighting
options available are:
1. Steady Warm White
2. Flashing Warm White
3. Fade In and Fade Out Warm White
4. Steady Multicolor
5. Flashing Multicolor
6. Fade In and Fade Out Multicolor
7. Sequential Multicolor & Warm White
8. Color Changing
These functions can be changed by pressing the foot pedal
switch or using the remote control. Please see the
instructions of remote control below.
Instruction of remote control
Please note this tree has a remote control.
Please pull out the insulation tape from the remote control, before starting
to use it.
1. Press Fn button, the function below cycle. Press the number key,
select from the following corresponding lighting functions:
Function 1: Steady Warm White
Function 2: Flashing Warm White
Function 3: Fade In and Fade Out Warm White
Function 4: Steady Multicolor
Function 5: Flashing Multicolor
Function 6: Fade In and Fade Out Multicolor
Function 7: Sequential Multicolor & Warm White
Function 8: Color Changing
There is memory mode on function adjustment.
If the remote control does not work, check whether the battery of the
remote control is out of power.
To replace the remote control battery:
1. Replace with a new button cell "CR2025" (3 volt) into
the compartment.
CAUTION:
DO NOT DISPOSE OF
BATTERIES IN FIRE. BATTERIES MAY EXPLODE
OR LEAK.
Operation
Turning on the tree
Step 1. Plug the well-connected power cord from the tree section (C)
into a proper outlet.
Maintenance
User Servicing Instructions
Replace the fuse.
a) Grasp plug and remove from the receptacle or other outlet device.
Do not unplug by pulling on cord.
b) Open fuse cover. Slide open fuse access cover on
top of attachment plug towards blades.
c) Remove fuse carefully.
d) Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse (provided
with product).
e) Close fuse cover. Slide closed the fuse access cover on top of
attachment plug.
f) Risk of fire. Do not replace attachment plug. Contains a safety
device (fuse) that should not be removed. Discard product if the
attachment plug is damaged.
Replace the lamp.
a) Grasp plug and remove from the receptacle or other outlet device. Do
not unplug by pulling on cord.
b) Pull lamp and plastic base straight out of lampholder.
c) Replace lamp with 3.0 volt, 20 mA type lamp(provided with product).
d) Lock the LED bulb.
CAUTION
To reduce the risk of overheating, replace burned-out lamps promptly.
1.
Use 3.0 Volt, 20 mA LED lamps only.
Risk of fire. This product does not contain lamp shunts, which allow the
2.
product to operate if one lamp burns out. Replace lamps only with the
spare lamps provided with this product.
If the new lamp base does not fit in lampholder, follow the steps below
before step c.
1. Pull the reflector out.
2. Remove the base of burned out
lamp by straightening lamp leads
and gently pulling lamp out.
3. Thread leads of new lamp through hole in old base with one lead in
each hole.
4. After lamp is fully inserted, bend each lead up, like other lamps in the
light set so that the leads will touch the contacts inside the
lampholder.
Need help?
Do you have a question about the 1007581501 and is the answer not in the manual?