Advertisement
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Brecknell SBI-505
Summary of Contents for Brecknell SBI-505
- Page 1 SBI-505 Indicator User Instructions AWT35-500827 Rev. A1...
-
Page 2: Table Of Contents
1.1 Contents Introduction on page 3 Installation on page 5 Basic Operation on page 7 If you choose clr n, the indicator exits the accumulation mode without clearing the total weight. If you choose clr y, the total weight is cleared and the indicator exits accumulation mode. -
Page 3: Introduction
1.2 Introduction For safe operation please read and follow all safety information and instructions. WARNING: Settings, calibration, inspection and maintenance should only be done by trained personnel. WARNING: This indicator is a static sensitive device. Remove power before making any electrical connections. - Page 4 1.2.2 Specifications: Accuracy class: 6000 e Resolution display: 30, 000 ADC: 2,000,000 Zero stability error: < 0.1μV//K Span stability error: < ± 6 ppm//K Sensitivity (internal): 0. 3V /d input voltage -30 ~ 30μmV DC Input voltage: 9-13.8 VDC: 0.3 amps (center terminal positive) Excitation circuit: 5 VDC, 4 wire connection maximum of 6 - 350Ω...
-
Page 5: Installation
1.3 Installation 1.3.1 Power Supply Connection The indicator is powered by an A/C adapter that plugs directly into the DC pin at the bottom of the indicator. The indicator accepts 9 - 12 VDC center positive adapter. 1.3.2 Connection of Loadcell and Indicator The indicator can be connected up to 6 - 350Ω... - Page 6 1.3.3 Communication interface Below is the RS232 DB9 pin: Pin assignments are shown below: DB9 joint Definition Function Sending data Receiving data Ground interface...
-
Page 7: Basic Operation
1.4 Basic Operation 1.4.1 Power Press and hold the ON/OFF key, shown below, for two seconds to power on or off the indicator. After a self-test, normal weighing mode will be accessed. 1.4.2 Zero Operation Initial Zero Setting During power up, if the weight on the scale is within the initial zero tolerance, the indicator will show zero automatically. - Page 8 1.5 Counting Function Follow these steps to count items of the same weight. 1.5.1 Getting a Piece Weight While in the weighing mode, press the Zero key to clear weight from the scale. Load pre-counted sample pieces of (5, 10, 20, 50, 100, 200, or 500) on the scale and press the Count key.
- Page 9 1.6 Accumulation Operation With 0 on the display, add the weight to the scale. Press the Total key to enter the accumulation mode. The Total annunciator turns on and the display shows n 001, and then the display goes back to the loaded weight. Unload the weight.
-
Page 10: If You Choose Clr N, The Indicator Exits The Accumulation Mode Without Clearing The Total Weight. If You Choose Clr Y, The Total Weight Is Cleared And The Indicator Exits Accumulation Mode
When the desired choice is displayed, press the Print key to accept that choice. If you choose clr n, the indicator exits the accumulation mode without clearing the total weight. If you choose clr y, the total weight is cleared and the indicator exits accumulation mode. -
Page 11: Calibration And Parameter Setting
1.7 Calibration and Parameter Setting The Parameter menu is divided into a calibration section and a parameter configuration section. To enter the parameter part of the menu, follow step 1 below. To enter the calibration plus the parameter section, follow step 2 below. You may need access to the Seal switch on the main board, shown in the photo below. - Page 12 Be sure to return the seal switch to its original setting once you are finished with calibration and configuration. The table below shows the name and symbol of each front panel key and their function while in the menu. Function Symbol Print Enter...
- Page 13 1.7.1 Calibration Instructions When initial installation or recalibration are necessary, locate the seal switch and place it in the ON position. The SBI-505 requires a minimum of 10% of the configured scale capacity in dead weight to calibrate the indicator.
- Page 14 Step Method of Operation Display Remark [C06 Span calibration options (6 is blinking) press 0= No span calibration [C06 press 1= Span calibration press [C06 Load weights on scales to 100% of capacity. [SPAN ] press Suggest close to the max capacity, at least [0100.00] 10% of max.capacity.
- Page 15 1.7.3 Application Function Parameters Setting Chart From step on page 11, parameter C08 will be displayed. Press to find the parameter to be changed. See the table below for information on available parameters. Function Parameter Parameters Setting and Instruction Options: 0 = no key tone Key tone Warning tone...
- Page 16 4= Indicator sends format continuously to a Communication setting computer. 5= Indicator sends format continuously to a host device compatible with RD65 remote display from Brecknell. Baud rate option: C19 Baud rate 0=1200/1=2400/2=4800/3=9600 Fixed 8,none & 1 stop bit Baud rate options: 0= Disable zero key 1=±1% max capacity...
- Page 17 Function Parameter Parameters Setting and Instruction Options: 0= Disable zero tracking 0.5=±0.5d 1.0=±1.0d 2.0=±2.0d 3.0=±3.0d Automatically zero 4.0=±4.0d tracking range 5.0=±5.0d AZT - Automatic Zero Note: 1. d = division tracking 2. the zero tracking range cannot bigger than manual zero range, see C20.
- Page 18 Function Parameter Parameters Setting and Instruction Dynamic filter Option: Instruction: Dynamic 0= Disable dynamic filter filter is collecting the 1=1 digital filter strength data filter before 2=2 digital filter strength loaded weight 3=3 digital filter strength Digital filter stable. When loaded 4=4 digital filter strength weight easily 5=5 digital filter strength...
-
Page 19: Output Format
1.8 Output Format 1.8.1 Option 1 - Not Available 1.8.2 Option 2 - PRINT key only By default, if you press the Print key while in net weighing mode, the following format will be sent to a peripheral device. In gross mode the first two lines will be left out of the format. - Page 20 1.8.3 Option 3 - Host commands When the indicator receives one of the commands shown in the table below, the indicator responds with a corresponding format. An example for the R command is shown below. Command word and role as follows: ASCII NAME Function...
- Page 21 = kilogram Polarity: + = Positive - = Negative 1.8.5 Option 5 - Host Device/Remote Display (RD65) Option 5 is compatible with the Brecknell RD65 remote display or host devices that can use the following output format: Gross/Net: Carriage Weight Data...
-
Page 22: Troubleshooting And Maintenance
1.9 Troubleshooting and Maintenance ERROR REASON SOLUTION 1. Overload 1. Reduce the weight 2. Wrong connection 2. Check load cell connection UUUUUU with load cell 3. Inspect load cell. Check the input and output 3. Load cell has voltage OR input and output resistance to problem. - Page 23 Parameter instruction Default Warning tone (key stroke) Automatic power-off Auto off UNIT key Upper limit alarm 000000 Lower limit alarm 000000 A to D counts Random number Date setting YYMMDD Time setting 24Hr.min.sec Serial interface data Serial interface Baud rate 3 (9600) Zero range Initial zero...
- Page 24 Brecknell 1000 Armstrong Dr., Fairmont, MN 56031 Toll free: 800-637-0529, Tel: 507-238-8702 Fax: 507-238-8271 Email: sales@brecknellscales.com www.brecknellscales.com Brecknell Foundry Lane Smethwick, West Midlands B66 2LP Tel: +44 (0) 845 246 6717 Fax: +44 (0) 845 246 6718 Email: sales@brecknellscales.co.uk www.brecknellscales.co.uk...
Need help?
Do you have a question about the SBI-505 and is the answer not in the manual?
Questions and answers
Model SB505 Digital Indicator, Brecknell 4 x 4' 10,000 lb Scale, can this scale be adapted to have HID interface? s/n 170921115
The provided information does not mention support for an HID (Human Interface Device) interface. The Brecknell SBI-505 scale supports RS232 communication via a DB9 connector. Therefore, based on the available details, it cannot be confirmed that the scale can be adapted to have an HID interface.
This answer is automatically generated