Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Boss Industries INFINITY 35
Summary of Contents for Boss Industries INFINITY 35
- Page 1 Product Manual INFINITY 35 Hydraulically Driven Air Compressor This manual must be read carefully before using your Boss Industries, LLC INFINITY 35. Store in a safe and convenient location for future reference. 310928 http://www.bossair.com 8/23/2016 AEM...
- Page 2 310928 - 2 -...
-
Page 3: Table Of Contents
Changing the Oil Filter........16 Changing the Air/Oil Coalescer......17 Changing the Air Intake Filter......17 Compressor Drive Belts.........18 Troubleshooting........19 Improper Discharge Pressure......19 Sump Pressure Does Not Blow Down...19 Oil Consumption..........19 Coalescer Plugging........20 High Compressor Discharge Temperature..20 Contacting Boss Industries, LLC....20 Warranty..........21 310928 - 3 -... -
Page 4: Welcome
Welcome General Information Thank you for choosing the Boss Industries, LLC INFINITY 35 Hydraulically Driven Air Compressor. Before operating, carefully read this manual and become well acquainted with your new machine. Doing this will increase your safety and maximize the life of the machine. -
Page 5: Safety
Safety General Safety Overview 310928 - 5 -... -
Page 6: Safety Precautions
Safety Safety Precautions The following safety precautions are a general guide to safe operation of the equipment. 310928 - 6 -... - Page 7 Safety Safety Precautions (continued) 310928 - 7 -...
-
Page 8: Specifications
Specifications Specification Sheet COMPRESSOR SPECIFICATIONS Model INFINITY 35 Type Hydraulically Driven Air Compressor Output Compressor RPM Hyd Flow Hyd Pressure 20 CFM @ 110 PSI 4400 8.2 GPM 1500 PSIG 25 CFM @ 110 PSI 5400 10.1 GPM 1500 PSIG... -
Page 9: Installation & Operation
Installation & Operation operation of other components on the vehicle. For example, if your vehicle is equipped with a crane, you must make sure the compressor will not interfere with the swing of the crane. In addition, the compressor should be installed in an area that permits cool ambient air to enter the air filter and the hot air to exhaust without recirculating into the machine. -
Page 10: Installation Of Air Storage Tanks
The installation of air storage tanks, if not done properly, will hinder the performance of the Pin C) Battery Ground rotary screw compressor. Boss Industries, LLC strongly discourages the use of an air storage tank as Pin D) 12VDC switched power for operation standard equipment for vehicle mounted rotary screw Pin ‘B’... -
Page 11: Connecting The Hydraulic Hoses
Lifetime Warranty Registration is a very critical area of inspection. The vehicle should not be moved until this Every Boss Industries, LLC INFINITY 35 machine inspection has been completed. comes standard with a lifetime warranty on the airend. In order to activate the lifetime coverage, the II. -
Page 12: Shutdown Procedure
Installation & Operation Operating Procedure I. Read this manual carefully before proceeding. II. Verify the service valve is closed. III. Engage hydraulic system. IV. Allow hydraulic system to run on bypass for 3-5 minutes to warm-up. V. Engage hydraulic flow to compressor. VI. -
Page 13: Maintenance
50-Hour Maintenance 80384 1-Year or 500-Hour 80385 Maintenance Kit Lifetime Warranty Information In order to maintain the lifetime warranty status on your INFINITY 35, the required maintenance intervals listed on the following page must be obeyed. 310928 - 13 -... -
Page 14: Maintenance Chart
Maintenance Maintenance Chart The MAINTENANCE CHART lists serviceable items on this compressor package. The items are listed according to their frequency of maintenance. INTERVAL REQUIRED MAINTENANCE 1. Check compressor oil level. EVERY 10 HOURS OR 2. Check for oil and air leaks. DAILY 3. -
Page 15: Compressor Oil
Maintenance Compressor Oil 310928 - 15 -... -
Page 16: Compressor Oil Fill, Level, And Drain
Maintenance Compressor Oil Fill, Level, and Changing the Oil Filter Drain The oil filter is a spin-on type element that is easily replaced through the maintenance access panel. First, Before adding or changing compressor oil, make sure remove the access panel from the right side (by the that the compressor is completely relieved of pressure. -
Page 17: Changing The Air/Oil Coalescer
Maintenance Changing the Air/Oil Coalescer Changing the Air Intake Filter The air/oil coalescer is a spin-on type element that is The air intake filter is a heavy-duty dry type high easily replaced through the maintenance access panel. efficiency filter designed to protect the compressor First, remove the access panel from the machine by from dust and foreign objects. -
Page 18: Compressor Drive Belts
Maintenance Compressor Drive Belts The 2-belt arrangement is sized for an average life of 1000 hours. This time frame can be increased or decreased depending on the end user’s periodic maintenance schedule. Drive belt tension should be checked for adjustment after the first 10 hours of operation and checked for adjustment every 100 hours there after. -
Page 19: Troubleshooting
Troubleshooting Sump Pressure Does Not Blow Down If after the compressor is shutdown, pressure does not automatically blow down (this process should take about 1 minute), check for: I. Blow down valve may be inoperative. II. Blow down valve exhaust port plugged. Blow down valve should have a 3/64”... -
Page 20: Coalescer Plugging
Boss Industries, LLC Service Department. compressor oil is breaking down. Phone: (800)635-6587 (USA) -
Page 21: Warranty
Warranty 310928 - 21 -...
Need help?
Do you have a question about the INFINITY 35 and is the answer not in the manual?
Questions and answers