Advertisement
INSTALLATION
Cutting the Hole
When the bracket is secure,
bend the tabs back against
the inside of the drywall and
Once you have decided
insert the screws so that they
upon an ideal installation
penetrate the tabs, clamping
location for the Wall-
the bracket to the drywall.
Mounted Volume Control,
(See Figure 7)
hold the Mounting Bracket
up to the wall surface. Level
the Mounting Bracket and
Running the
mark the wall by tracing the
Speaker Cable
inside perimeter of the
Mounting Bracket with a
Conceal the Speaker Cable
pencil. Repeat the same
between the stereo equip-
procedure for the In-Wall
ment and the Wall-Mount
Speakers using the supplied
Volume Control, and
template to trace a 9-1/4"
between the Wall-Mount
diameter hole for each In-
Volume Control and the
Wall Speaker.
Speakers.
(See Figure 3)
Be sure to measure the
!
If you are cutting a painted
approximate distance
or wallpapered ceiling, use
from your equipment to
a razor-knife to cleanly cut
the Wall-Mount Volume
the wallpaper. Then use a
Control location, and from
drywall saw to cut the dry-
the Wall-Mount Volume
wall. (See Figure 4)
Control to the first and
second Speaker locations
Be very careful not to saw
!
to ensure that you have
through existing wires,
enough wire to complete
pipes or structure.
the installation.
y z
y
z |
Installing the
(See Figure 8)
Mounting Bracket
Figure 6
Place the Mounting Bracket
y
|
against the hole.
(See Figure 5)
Bend the tabs at a 90° angle
and insert into the hole.
(See Figure 6)
Figure 3
Figure 4
|
z
|
y
z
Figure 5
|
z
y
|
|
y z
y y zy
y z
|
|
|
Figure 7
5
INSTALLATION
Connecting the
conductors and remove 1/4"
Speaker Cable to
of insulation from the end of
the Volume Control
each conductor. Twist the
end of each conductor so
the ends are not frayed.
!
Connecting the Volume
Make sure that no more than
Control backwards could
1/4" of bare wire is exposed.
damage your amplifier.
Make sure to connect the
Exposing too much wire
!
Speaker Cable coming
could cause the wires to
from your amplifier to
touch and create a "short"
the INPUT of the Volume
which could damage
Control (labeled AMPLIFI-
your equipment.
ER), and the OUTPUT of
the Volume Control
||
zz
||
zz
y
y
Connect the exposed ends
(labeled SPEAKERS) to
of each of the Speaker
the In-Wall Speakers.
Cable's conductors to the
removable connectors pack-
Strip the wire jacket back 2"
aged with the Wall-Mount
to expose the four colored
Figure 8
white
red and black
green
(unused)
Left Speaker
Inset
red
black
red black
white
green
Volume Control. (See
"Connect the wires" on
the bottom of Page 7.)
If you are going to connect
more than two pairs of
speakers to the amplifier,
the Volume Control's
"Impedance Magnifying"
jumpers must be reset.
(See Figure 10, Page 8
of this manual)
Refer to the Installation
yy
z z
| |
section on page 8 of the
VCS-2D-IM Volume Control
manual included with your
Music Anywhere! In-Wall Kit
for detailed instructions.
yy
see
Inset
|
to "speaker"
connection on
volume control
Right Speaker
!
Carefully make a 12" incision in
the wire jacket to expose all four
colored conductors (be careful
not to damage the colored
conductors inside!).
Cut only the red and black wires
at the top of the incision and strip
approx. 3/8" of insulation from the
ends of each conductor. Connect
the red and black wires to the
speaker as shown above.
6
Advertisement
