Reyee RG-E5 - Mesh Router Manual

Scan to Download Reyee Router App

Packing List

Product Appearance

Reyee Mesh Indicator

System Status Indicator

Scenario 1: Configure one single router to access the Internet

1. Power on and connect Ethernet Cable.
   
2. Configure the router.
   The router will complete startup in 2 to 3 minutes after being powered on. Wait until the system status indicator turns solid on and the SSID is broadcast (default SSID: @Reyee-sXXXX).

Access the Internet by Web

1. Go to your phone settings page and choose Wi-Fi network @Reyee-sXXXX, and the configuration page will appear automatically. Or you can access 192.168.110.1 via the browser.
   
2. The router automatically detects the type of Internet connection. Please configure the network parameters accordingly.
   
3. The Wi-Fi configuration takes effect in 2 to 3 minutes. Connect to the new Wi-Fi name (SSID) after it appears in the Wi-Fi list for Internet access.
   

Access the Internet by App

1. Download the Reyee Router App
   
   
   
2. Create an account by one click
   
3. Tap Add Router, and follow the guide of configuration
   

Scenario 2: Configure more than one router to set up a Mesh network

To cover every corner of a villa, a large house or a condo, you can buy multiple Reyee Mesh routers to form a mesh network for full-house coverage.

1. Make the primary router connect to the internet
   Please refer to Scenario 1 for configuration.
2. Place the secondary router within a maximum distance of 2 meters(around 6.5ft) from the primary router, and power it on
   Wait for 2 to 3 minutes until the system status indicator on the secondary router turns solid on. If the router has been configured before, please use a pin to press Reset Button for over 3 seconds to restore the factory settings.
3. Press the Reyee Mesh button on the primary router
   The Reyee Mesh indicator on the primary router will blink in green, indicating that the primary router is searching nearby routers for pairing. The Reyee Mesh indicator on the secondary router will also blink in green, indicating the secondary router is being paired with the primary router. In about 2 minutes, the Reyee Mesh indicators on both routers will turn solid green, indicating Mesh pairing is complete.
   
4. Place the secondary router in an area where the Wi-Fi signal is weak or nonexistent, and power it on again
   Wait for 3 to 5 minutes until the Reyee Mesh indicator on the secondary router turns solid on. The original SSID of the secondary router (@Reyee-sXXXX) will disappear and both routers will broadcast the same SSID, indicating that Mesh networking succeeds.
   You can also set up a wired connection between two routers as shown below.
   
   • Determine the placement and distance by referring to the signal strength visualized by Reyee Mesh indicators on the top.
   • Please find the proper location for both routers. Do not place two routers too far away from each other and avoid too many walls or other obstacles between them.
   • If you have three or more routers, you can pair them by one-click Reyee Mesh during startup, or repeat step 2 to 4 to connect them one by one. A Reyee mesh network consists of up to five routers (one primary router and four secondary routers).

FAQs

1. What can I do if I forget the management password?
   Try the Wi-Fi password which may be the same with the management password. If it does not work, please restore the device to factory settings.
2. How to restore the factory settings?
   Power on the router and wait for 2 to 3 minutes until it completes startup. Use a pin to press the Reset Button for over 3 seconds until the system status indicator starts blinking, and then release the button. After the system status indicator turns solid on, the router will broadcast SSID @Rey-ee-sXXXX, indicating that the router is restored to factory settings successfully.
3. Can I connect routers with an Ethernet cable?
   Yes, and wired connection is more stable. Insert one end of the Ethernet cable into the WAN port (yellow) of the secondary router and connect the other end to the LAN port (black) of the primary router.