IMPORTANT: Before starting the equipment, read the contents of this manual, which must be stored in a place familiar to all users for the entire operative life-span of the machine. This equipment must be used solely for welding operations. www.celette.com Page No: 3...
Do not spot weld where flying sparks can strike flammable material. Protect yourself and others from flying sparks and hot metal. Be alert that welding sparks can easily go through small cracks and openings to adjacent areas. Watch for fire, and keep a fire extinguisher nearby. www.celette.com Page No: 4...
Page 5
Wear body protection made from durable, flame-resistant material (leather, heavy cotton, wool). Body protection includes oil-free clothing such as leather gloves, heavy shirt, cuffless trousers, high shoes, and a cap. P rotect others in nearby areas by using approved flame-resistant or noncombustible fire curtains or shields. Have all nearby persons wear safety glasses with side shields. www.celette.com Page No: 5...
Secure unit during transport so it cannot tip or fall. READ INSTRUCTIONS: Read and follow all labels and the Owner’s Manual carefully before installing, operating, or servicing unit. Read the safety information at the beginning of the manual and in each section. www.celette.com Page No: 6...
The model of the machine CE, EN, ISO International standards Rated supply voltage Range of rated ac no-load voltage and number of adjustable steps I1(MAX) Max input welding current I2(MAX) Max output welding current DUTY Duty cycle www.celette.com Page No: 7...
If the strength is not enough, please adjust the torch pressure. The work process is electric discharge, stud welding and recharge, repeat the steps. Traditional method, such as rivets, lock screw and common welding, they must damage the base metal. But the stud welding does not damage the base metal. www.celette.com Page No: 8...
1. Cable must connect the base metal directly, and must connect more than two earth cables. 2. The earth cable must connect on the diagonal position of the base metal. (refer to the diagram as follow). www.celette.com Page No: 9...
The cable connection, please refer to above the diagram. Carbon electrode heating (optional function, only for carbon heating type machine). SPOT WELDING TORCH. USE ONE EARTH CABLE OR TWO EARTH CABLE CONTROL CABLE SPOT WELDING TORCH CABLE SPOT WELDING TORCH EARTH CABLES WORK PIECE www.celette.com Page No: 10...
Round washer/ tab shooter Quick puller slide hammer Star washer/steel tab Triangle washer/ American stud Choose the welding mode, the system will auto match welding power. And the power indicator display the power level 1-10 on the right side. www.celette.com Page No: 11...
The welding torch will discharge by contact way. That applies to: Soft steel, stainless steel stud screw. Length of stud screw less than 150mm. TORCH HEAD HOLDER SHELL 3 SUPPORT FEET PRESSURE ADJUSTMENT SCREW CLAMP HANDLE TRIGGER www.celette.com Page No: 12...
That can make sure the screw camp and stud screw close contact. The groove expand in use, the stud screw will loose. Use pliers to clamp it, when meet the problem, that can extend using life of the screw clamp. www.celette.com Page No: 13...
5. Turn off the switch, when not use the machine. 3.11 SELECT STUD SCREW: Metal: Soft steel, stainless steel, aluminium, titanium (Ti), brass, copper. 1. Model SCREW DIAMETER THREAD DIAMETER TOTAL TOTAL TOTAL LENGTH LENGTH LENGTH www.celette.com Page No: 14...
Page 15
Defective AL stud: The embossment is not in the center of stud’s end face. The top face of embossment is not smooth. The size and height of the embossments are unevenness. The end face of stud is coarse. COARSE DEFECTIVE AI STUD www.celette.com Page No: 15...
4. Check transformer, maybe over heat 5. Please contact to the manufacturer 1. Check the power of fan Fan is not working 2. Check the fan, maybe something stuck in the fan 3. Please contact to the manufacturer www.celette.com Page No: 16...