BaBylissMEN T890E, T158B - Bear Trimmer Manual and Video Review

Please carefully read the safety instructions before using the product.

CHARGING THE APPLIANCE

Only use the adaptor supplied with the appliance.

1. Insert plug into appliance and connect the adapter, making sure the trimmer is in the OFF position. Before using the appliance for the first time, charge it for 3 hours.
2. Check that the charging indicator light is flashing.
3. A full charge provides 120 minutes of cordless use
4. Subsequent charges should be 2 hours after the initial 3 hours.

Your BaBylissMEN Beard Trimmer is equipped with Li-ion batteries. Before using for the first time, the appliance should be fully charged continuously for 3 hours. This initial super-charge ensures optimum power performance to ensure smooth fast trimming every time. Maximum battery capacity will only be reached after 3 charging and discharging cycles.

PRESERVING THE BATTERIES

In order to maintain the optimum capacity of the rechargeable batteries, the trimmer should be fully discharged and then recharged for 3 hours every 6 months.

MAINS OPERATION

• Ensure the appliance is switched off.
• Connect the adaptor to the base of the appliance and plug the adaptor into a suitable mains socket.
• The blue LED charging light will flash when adaptor is correctly inserted into the appliance and connected to the mains.
• The appliance is now ready for use.

NOTE: The appliance should not be used for longer than 20 minutes when operated from the mains.

CORDLESS OPERATION

Ensure appliance is charged for minimum of 30 minutes. the blue LED charging light will flash when the adaptor is correctly inserted into appliance and connected to the mains.

Once the appliance is fully charged the blue LED charging light will stop flashing but remain on. Remove the mains cord form the appliance, turn on and use as required.

PREPARATION FOR USE

• Always inspect the appliance before use for noticeable signs of damage. Do not use if damaged.
• Ensure the blades are free from hair and debris.
• Ensure the appliance is sufficiently charged.
• Use on clean, dry hair that has been combed until tangle free.

USING THE LENGTH CONTROL DIAL

The length control dial allows you to adjust the comb guide to change the cutting length of your trimmer. You'll need to experiment to find your preferred length, but as a guide, 1mm will give you a very short be a stubble beard and 12mm with be thicker and longer.

• Select a cutting length (1-12mm) using the dial on the front of the trimmer.
• Turning the dial clockwise will increase the cutting length.
• Turning it anti-clockwise will decrease the cutting length.
• Once you have selected your desired cutting length, the guide automatically locks into position for a guaranteed, even cut.
• Switch the trimmer on by sliding the power button up, the blades will start to move and you can begin trimming.

USING THE TRIMMER WITHOUT THE COMB GUIDE

• The trimmer can also be used for detailing/ shaping around the edge of the beard.
• To remove the comb guide, place two fingers either side of the wheel and gently pull to unclick the guide. (Fig. 1)
  
• Pull the guide up and away from the trimmer unit.

ATTACHING THE COMB GUIDE TO THE TRIMMER

• Slide the trimmer head under the back lip of the guide.
• The guide should rest on the head.
• Click the guide into position by gently pressing the wheel against the unit. (Fig. 2)
  
• The guide should click into a secure position

CLEANING AND MAINTENANCE

To maintain optimum performance, the appliance should be cleaned after each use:

• Remove the comb guide after use. Rinse the comb guide under running water and dry thoroughly before storage or use.
• Use the cleaning brush supplied to brush away any hair and debris.
  Do not use a sharp object to clean the trimmer blade.
• The blades can be removed to aid cleaning.
• To remove the blades, hold the handle of the trimmer with one hand, place your thumb underneath the blades and push the blades away from the handle. (Fig. 3)
  
• To re-attach the blades, ensure the base of the blade plate is seated in the handle and click into position.
• Gently blow away any hair trapped beneath the blades.
• The blades can be rinsed under the tap.
• Ensure the trimmer blades are dry before re-attaching to the trimmer body.
• After cleaning, switch the appliance on and oil the blades using a few drops of the lubricating oil supplied. Only use the lubricating oil supplied with the appliance as this is specifically formulated for high speed trimmer and does not evaporate or slow the blades.

BABYLISS SARL
99 avenue Aristide Briand
92120 Montrouge
France

www.babyliss.com

FAC / 2019 / 06