Zipato ZIPABOX 433MHz Module Quick Installation Guide

Zipato ZIPABOX 433MHz Module Quick Installation Guide

Also See for ZIPABOX:

Advertisement

Zipato ZIPABOX 433MHz Module Quick Installation Guide

INTRODUCTION

TRADEMARKS
Zipato and the Zipato logo are registered Trademarks. All other product names mentioned herein may be trademarks or registered trademarks of their respective companies.

warning
NOTICE: Although Zipato has attempted to ensure the accuracy of the content of this manual, it is possible that this document may contain technical inaccuracies, typographical, or other errors. Zipato assumes no liability for any error in this publication, and for damages, whether direct, indirect, incidental, and consequential or otherwise, that may result from such error, including, but not limited to loss of data or profi ts. Zipato provides this publication "as is" without warranty of any kind, either express or implied, including, but not limited to implied warranties of merchantability or fi tness for a particular purpose. The published information in the manual is subject to change without notice. Zipato reserves the right to make changes in the product design, layout, and driver revisions without notifi cation to its users. This version of the Installation guide supersedes all previous versions.

ELECTROMAGNETIC COMPATIBILITY

In proper state and when operated properly, the product complies with all the requirements in respect of interference radiation according to EN 301 489-17, EN 301 489-1 and EN 300 328. The connections conducting HF signals must neither be manipulated nor damaged.

TAKE CARE OF YOUR SAFETY

Display extreme caution when using ladders or steps, please follow manufacturer's instructions. Be careful when using hand and power tools and follow the manufacturer's guidelines when using them. Take care that the correct tools are used. Wear goggles or protective clothing where required.


RISK OF ELECTROCUTION: All work on the device should only be carried out by trained and skilled electricians. Observe the country-specifi c regulations.


The connected devices and the fl ush-mounted receiver can become damaged if devices are operated that do not correspond to the technical specifi cations (see technical data).


RISK OF FATAL INJURY FROM ELECTRIC CURRENT. The device has no basic insulation and must therefore be installed in a way that protects against accidental contact.


RISK OF FATAL INJURY FROM ELECTRIC CURRENT. When installing a wall plate, the distance between the cover's fi xing brackets or screws and the connections of the fl ush - mounted MM Switch Single must be at least 4 mm once installed. If the distance is less than 4 mm, a deeper installation box must be used. The fi xing brackets or screws of the cover must not press against the housing. Only insulated tools may be used for operation on the device, e.g. an insulated phase tester.

Device Overview - Part 1

COMPATIBILITY

This Expansion Module is designed to work only with Zipabox.

HANDLING

Do not drop, knock or shake the module. Rough handling can break internal circuit boards and connectors.

ENVIRONMENT

Do not expose the module to excessive heat or cold, as it can damage or shorten the life of electronic circuit boards.

If possible, dispose this module at a recycling center. Do not dispose of this module with the household waste.

Device Overview - Part 2

TECHNICAL MANUALS

TECHNICAL DETAILS

POWER SUPPLY Fom Zipabox
OPERATING TEMPERATURE -10° ~ +40°C
OPERATING HUMIDITY 5 ~ 95% RH
DIMENSIONS 29 x 87 x 46 mm (without antenna)
WEIGHT 62g (with antenna)
COMMUNICATION FREQUENCY 433 MHz
COMMUNICATION PROTOCOL ZigBee
COMMUNICATION RANGE Up to 30m indoor or 70m outdoor

UNPACKING
Zipabox 433MHz Module consists of:

  • 1x Expansion Module
  • 1x 433 MHz antenna

warning
PLEASE NOTE: Connect antenna by screwing it clockwise to the connector on the module

CONNECTING DEVICE

  1. Disconnect Zipabox from power

CONNECTING DEVICE

  1. Align connector of Zipabox 433 Expansion Module to expansion Slot 2 of Zipabox (or to module connected into Slot 2)
  2. Join module and Zipabox together until gap between them is completely closed.

INSTALLATION / MOUNTING

Mount together with Zipabox.

INTERFERENCE

All wireless devices are subject to interference, which could affect device performance.

REPARING

Do not attempt to repair this product. There are no user-serviceable parts inside.

WATER-RESISTANCE

This product is not water-resistant. Keep it dry. Moisture will corrode the inner electronics.

CLEANING

Use a dry cloth to clean this product. Do not use harsh chemicals, cleaning solvents or strong detergents.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Zipato ZIPABOX 433MHz Module Quick Installation Guide

Advertisement

Need Assistance?

Do you have a question about the ZIPABOX that isn't answered in the manual? Leave your question here.

Error while submitting your question. Please, reload page and try again.

Thank you! Your question has been received!

Table of Contents