%./01/02 REVISIONS Software Service Manual (Document) INSTRUMENT VIEWS INSTALLATION Equipment Technical Data Safety Standard Approvals OPERATION INSTRUCTION Warm Up Test Selection Stop Watch Calibration Default Test Values Measurement Measurement Stop Autostart SERVICE Service Functions Total Default Values Temperature Adjustment Optic Adjustment 5.4.1 OD Correction 5.4.2...
Page 3
03,4)5$67)&78()9&$+: 2/26 Service Manual HumaClot Junior...
Page 4
0514()-)+ "**2#"$0)+ -."-+ 4#5,20-+ ,)#%/),+ ;#51+ .21"$+ >(55,+ =%((+ $5-+ -#"$*1%-+ .)4"-%-%*<+ A:CD<+ 5#+ 5-.)# %$;)0-%52*+ ,%*)"*)*<+ "44#54#%"-)+ 4#)0"2-%5$*+ *.52(,+ >)+ -"B)$+ >3+ -.)+ %$*-#21)$-+ 54)#"-5#9+ :$+ 0"*)+ 5; 4("*1"+*4%((),+5$+-.)+%$*-#21)$-<+0()"$+=%-.+"+4"4)#+-5=)(+*5"B),+%$+EFG+>()"0.9 The !"#$%&'()*"+,'- is manufactured for HUMAN GmbH. Company Address: HUMAN GmbH...
;) <1=>2>./2 ;?;) 2'8(@$-7 <7A? B'C,8,D$(,'+ <7#$-: C 5.14 Test adaptations First release For PC/AT3/DD ;?E) 27-A,D7)B$+"$&)FG'D"#7+(H <7A? <787-7+D7)2'8(@$-7 <7#$-: C 5.14 First edition 4/26 Service Manual HumaClot Junior...
Figure: Front view Screws (2) to open instrument Serial No. Figure: Rear view Interface for printer DC-Input 12V/1A or data transmission Sub D9 pole Pin 2 data send Pin 3 data receive Pin 5 ground Service Manual HumaClot Junior 5/26...
Page 7
On/Off !"#$%&'()*"+,'- Optic start Cursor up Cursor down Timer / Stopwatch Enter Test Menu Service / Mailfunction Ready to use Optic channel Figure: The Front panel 6/26 Service Manual HumaClot Junior...
:7O)X074(X? Change active test with the TEST D"-4'-):7O4. Confirm active test with the FIB: :7O)X1+(7-X. To alternate among the tests, press key X074(X to activate test selection, D"-4'-):7O4 to change and key 1+(7- to confirm? Service Manual HumaClot Junior 9/26...
( i.e. fibrinogen, thrombin ) this feature does not work properly because the change in the signal is too small. In this case, inject the reagent quickly and with more force into cuvette and/or press the key Z'5(,D\ again. 12/26 Service Manual HumaClot Junior...
LOAD DEFAULT ? key "0,#7-" ` "1+(7-" The following service procedures can be performed on the !"#$%&'()*"+,'-R <747()(')C78$"&()A$&"74 07#57-$("-7)$Ca"4(#7+( .GbD'--7D(,'+ %'$6?bD'--7D(,'+ .5(,D)D37D: 27()<2EKE Use the D"-4'-):7O4 to change and the :7O)X1+(7-X to confirm ! >+D'--7D()$Ca"4(#7+(4)@,&&),+8&"7+D7)(37)#7$4"-7#7+()4,6+,8,D$+(&Oc)d78'-7)D3$+6,+6)$+O(3,+6^)97)$@$-7 '8)(37)D'+47N"7+D74c Service Manual HumaClot Junior 13/26...
Wait until a stable temperature of 37.0°C is displayed on the !"#$%&'()*"+,'-. Check and correct the system temperature if not equivalent to the external thermometer. Use the Up / Down keys to increase or decrease of temperature Service Manual HumaClot Junior 15/26...
With the COAG CORRECTION the instrument can correct the result for better correlation to other systems or reagents. Example: On another instrument a plasma sample measures with PT = 12.1 seconds; on the HumaClot Junior the result is 11.0 seconds. To get equal results, the result has to be corrected by factor of 1.10 (+10%).
The OPTIC CHECK is recommend, if problems with measurements arise. Remove the cuvette from optic. OPTIC CHECK mw = ;;KEK The HumaClot Junior has adjusted this optic value (mw) to 11323 at an amplification (amp) of level 14. Control range: (ensure that no cuvette is placed in the optic) ;QQQQ)f);KQQQ...
This can happen, if there is not sufficient light (i.e. with very turbid reagents or lipemic samples). Change to HUMAN reagent . Avoid extreme samples. there is too-intense light (i.e. direct sunlight). Protect against sunlight. LED is burned out. Replace device.
Page 20
Always repeat the sample to verify the result. Possible reasons includes the following: Incorrect reagent Air bubbles Debris in cuvette Low fibrinogen level Sample improperly collected Optic is incorrectly adjusted Action: Use recommended materials Increase OD-Correction slightly Decrease OD-Range Service Manual HumaClot Junior 19/26...
Remove the four EJOT screws with the screwdriver e) Remove the M3x6 screw with the ground cable f) Unplug the keyboard cable from system board connector g) Lift up the complete inner assembly from the top case 20/26 Service Manual HumaClot Junior...
Page 22
Remove the four screws from the display and unplug the cable i) Lift up the complete heating block away from the system board sockets and spacers. !7$(,+6)8',& 07#5? 47+4'- ))))))).5(,D)9&'D: ]-'"+C,+6)D'++7D(,'+4 Service Manual HumaClot Junior 21/26...
Page 23
DC Input RS232 Microcontroller System board Keyboard connection Microcontroller Ground Battery DC Input '()*+,-./+0 +/11#+)*/12 RS232 22/26 Service Manual HumaClot Junior...
This will stop the measurement and show the virtual result. If the system board, heating components or microcontroller has been changed, a temperature check should be done before the final QC (Quality Control) procedure. Service Manual HumaClot Junior 23/26...
Need help?
Do you have a question about the HumaClot Junior and is the answer not in the manual?
Questions and answers