Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HAISEN HD020SR
Summary of Contents for HAISEN HD020SR
- Page 1 Microwave Motion Sensor PRODUCT SPECIFICATION CUSTOMER： Microwave Motion Sensor with Dual Circuit Output Control for LED Light & Sterilamp PRODUCT： HD020SR MODEL NO： PREPARED： CHECKED： 2020.6.2 APPROVED： DATE： CUSTOMER RECEIVED: CHECKED APPROVED DATE...
-
Page 2: Technical Data
2. Built-in installation, mounting height 3M, all tested indoor, actual test data shall be subject to the customer's actual test. * It's equipped with remote control, please refer to the parameter setting and remote control instruction on page 8-HD03R Shenzhen Haisen Technology Co., Ltd., Tel: +86-755-82598105 丨Fax: +86-755-82598106丨Email: info@haisensz.com 丨www.haisensz.com Haisen Technology | 01... -
Page 3: Mechanical Structure
Work time Dimensions (Unit: mm) Note: HD02VR-3 Wire diameter 4mm,Standard Version Cable Length 485±10mm(can be customized). 76.1 41.3 ø3.8 24.4 35.2 ø4 23.2 Wiring diagram Shenzhen Haisen Technology Co., Ltd., Tel: +86-755-82598105 丨Fax: +86-755-82598106丨Email: info@haisensz.com 丨www.haisensz.com Haisen Technology | 02... -
Page 4: Buckle Installation
1. No metal object shielded on the module; 2. The microwave module with hole should not be behind the lamp board, but protrude on the lamp board. Shenzhen Haisen Technology Co., Ltd., Tel: +86-755-82598105 丨Fax: +86-755-82598106丨Email: info@haisensz.com 丨www.haisensz.com Haisen Technology | 03... -
Page 5: Detection Coverage
This figure indicates the maximum distance at the highest mounting height with 100% sensitivity. Typical installation height 2.5-6m Ceiling Mounted Wall Mounted Mounting Mounting height height Well covered Covered Shenzhen Haisen Technology Co., Ltd., Tel: +86-755-82598105 丨Fax: +86-755-82598106丨Email: info@haisensz.com 丨www.haisensz.com Haisen Technology | 04... - Page 6 To say when it change from L2 to L1 mode, the work time would be retimed when back to L2 mode. The sterilamp couldn't detect daylight. When power on, LED light will need 10s before turn on and sterilamp will not. Shenzhen Haisen Technology Co., Ltd., Tel: +86-755-82598105 丨Fax: +86-755-82598106丨Email: info@haisensz.com 丨www.haisensz.com Haisen Technology | 05...
- Page 7 Hold time could be set to 5s/10min. Sterilamp OFF after the work time until the next round start when the sensor detect movement. Shenzhen Haisen Technology Co., Ltd., Tel: +86-755-82598105 丨Fax: +86-755-82598106丨Email: info@haisensz.com 丨www.haisensz.com Haisen Technology | 06...
- Page 8 ON/OFF based on the time after people leave. recycling. daylight threshold setting Otherwise sterilamp start to (Refer to point 1/2/3 above). work after people leave. Shenzhen Haisen Technology Co., Ltd., Tel: +86-755-82598105 丨Fax: +86-755-82598106丨Email: info@haisensz.com 丨www.haisensz.com Haisen Technology | 07...
- Page 9 100% with LED light on for 2s, then sterilamp (2s) (test mode） turn on 2s. Daylight disable. This remote control keys instruction could be only used for HD020SR which is Remarks different from the standard HD03R. HD03R Remote Control Operation Steps Notes When the work time is set to"+∞', sterilamp OFF when...
-
Page 10: Installation Precautions
3. Detection area will be affected by speed of motion, mounting height and movement volume. 4. Conduct test on sunny days without the lampshade which will affect the tested lux value. Shenzhen Haisen Technology Co., Ltd., Tel: +86-755-82598105 丨Fax: +86-755-82598106丨Email: info@haisensz.com 丨www.haisensz.com Haisen Technology | 09...