Table of Contents
Advertisement
Quick Links
64-Channel, 2A Multiconfig Multiplexer
This document is a technical description of the YAV90059 .
Note Before you begin, complete the software and hardware installation procedures applicable to your
application.
Note the guidelines in this document are specific to the YAV90059 . The other components in the system
might not meet the same safety ratings. Refer to the documentation of each component in the system to determine
the safety and EMC ratings for the entire system.
MORE INFORMATION ON OUR WEBTSITE:
www.6tlengineering.com
TECHNICAL DESCRIPTION
YAV90059
Advertisement
Table of Contents
Related Manuals for 6TL YAV90059
Summary of Contents for 6TL YAV90059
- Page 1 Note Before you begin, complete the software and hardware installation procedures applicable to your application. Note the guidelines in this document are specific to the YAV90059 . The other components in the system might not meet the same safety ratings. Refer to the documentation of each component in the system to determine the safety and EMC ratings for the entire system.
-
Page 2: Table Of Contents
LED BEHAVIOUR ......................8 SWITCH CONFIGURATION................... 9 HARDWARE SPECIFICATIONS .................. 10 OPERATION ........................ 11 11.1 PHI6 EXPLORER soft interface ................ 11 LOW LEVEL CAN COMMANDS ................... 12 ACCESSORIES ......................12 UNPACKAGING AND INSTALLING ................13 Pag 2 | 13 www.6tlengineering.com 24/06/2022 YAV90059... -
Page 3: Safety Guidelines
ELECTROMAGNETIC COMPATIBILITY GUIDELINES The product YAV90059 to which this manual relates meet the provisions of the EU Directives 2014/30/CE which declares the compliance of electromagnetic compatibility (EMC) and directive 2014/35/CE of low voltages electronic devices. -
Page 4: Description
DESCRIPTION The YAV90059 module is controlled through CAN Bus and features104 DPST relays forming two 4-poles, 2-Poles or 1-Pole Multi-configuration Multiplexers. The configuration of the multiplexer is selected by a software command. The ‘mode’ is an analog output Phi6 function, where the input parameter can be 1 to 13. The modes available are the following: 1. -
Page 5: Layout And Dimensions
LAYOUT AND DIMENSIONS All dimensions are in millimetres. Pag 5 | 13 www.6tlengineering.com 24/06/2022 YAV90059... -
Page 6: Relay Distribution
RELAY DISTRIBUTION Pag 6 | 13 www.6tlengineering.com 24/06/2022 YAV90059... -
Page 7: Pinout (Front)
Mux# 7 Comm- Mux# 7 K110 + Mux# 7 K110 - Mux# 7 K109+ Mux# 7 K109 - Mux# 7 K112 + Mux# 7 K112 - Mux# 7 K111 + Mux# 7 K111 - Pag 7 | 13 www.6tlengineering.com 24/06/2022 YAV90059... -
Page 8: Connector Pinout (Rear)
Solid green Board is powered on, but firmware of microcontroller is not present or is not running due an error. Blinking green Board is powered on and firmware is running properly. LED behaviour Pag 8 | 13 www.6tlengineering.com 24/06/2022 YAV90059... -
Page 9: Switch Configuration
RESET Must be OPEN on operation. A temporary bridge causes a reset of the board. CAN-END Placing jumper adds a 120 Ohm resistor between the CAN-High and CAN-Low signals of CAN-Bus. Switches description Pag 9 | 13 www.6tlengineering.com 24/06/2022 YAV90059... -
Page 10: Hardware Specifications
Max. Units • Maximum switching voltage • Rated current • Switching power • Minimum switching voltage • Operate time • Release time • Bounce time • mΩ Initial contact resistance Relay contact specifications Pag 10 | 13 www.6tlengineering.com 24/06/2022 YAV90059... -
Page 11: Operation
11. OPERATION Through the PHI6 Explorer soft panel the user can interface with the YAV90059 board manually. This tool is a very useful for table-top debugging of test-systems or system maintenance on-site. The panel displays the relays in two pages, 4 banks in each page. -
Page 12: Low Level Can Commands
12. LOW LEVEL CAN COMMANDS 13. ACCESSORIES Item Description ITA Module Quadrapaddle Signal Module, 192 Position VP510151105 ITA Quadrapaddle pin Quadrapaddle Signal, Contact, 7 Amp, 20-24 AWG VP610138109 Pag 12 | 13 www.6tlengineering.com 24/06/2022 YAV90059... -
Page 13: Unpackaging And Installing
To start using the product just remove vacuum bag carefully to avoid damage. To install the YAV90059 simply insert the module on a VPC receiver, vertical or horizontally, according to the Receiver arrangement. Once it is completely inserted, fix YAV module with two 4-40 UNC screws on each side of connector.