Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Supratech ASKA FOAM
Summary of Contents for Supratech ASKA FOAM
- Page 1 M A I N T E N A N C E G U I D E G U I D E F O A M S O A P D I S P E N S E R S ASKA FOAM TOUCH FREE FOAM ELITE FOAM...
- Page 2 SUPRATECH assumes no responsibility for errors or omissions in the information presented in this document. In no event shall SUPRATECH be liable for any special, incidental, indirect or consequential damages of any kind, or any damages whatsoever arising out of or in connection with the use or performance of this information.
-
Page 3: Technical Data
T E C H N I C A L DATA FOAM SOAP DISPENSERS ASKA RES-55M ELITE RES-72M TOUCH FREE RES-84M Capacity: 1 liter. Power supply: 12 V transformer. Soap viscosity: 0 - 100 cPs. Standard discharge: Varies according to viscosity and “foamability” Sensor range: 30-100 mm, ±... -
Page 4: Pre-Installation Information
SUPRATECH foam soap dispensers are suitable for use with any generic soap of the correct viscosity and pH. The pH level of all soap used in SUPRATECH soap dispensers should be between 6.5 to 8.5. Lower levels will cause corrosion to the metal dispenser and even the rubber and plastic components. -
Page 5: Pack Contents
PACK CONTENTS RODEO RES-22 / RES-23 Familiarize yourself with the part names and ensure that all the parts are included in your package. 1 x body et accessories 1 x foam compressor with pipe 1 x pump assemlbly with bottle support and soap tank 1 x quick connection fitting 1 x 12V transformer... -
Page 6: Installation
I N S TA L L AT I O N Step 1 : Remove all mounting hardware Drill a hole (25-29mm) in the deck or lavatory for the soap dispenser body and a small hole for the anti rotation pin. Disassemble the nut, disk and gasket from the base of the soap dispenser body. - Page 7 I N S TA L L AT I O N Fix the bottle support to the desired location. The pump MUST be within reach range of the Com cable and black supply tube. Connect the pipe from the dispenser to the quick connection fitting of the compressor.
- Page 8 I N S TA L L AT I O N Step 3 : Connecting the power source Remove the protective sticker covering the sensor. Connect the soap dispenser pump connector to its matching connector O’RING VISIBLE - NOT CONNECTED PROPERLY coming from the electronic unit.
-
Page 9: Filling The Soap Tank
FILLING THE SOAP TANK Unscrew the soap tank from the pump assembly and pull it out from the bottle support. Fill in the liquid soap up to the top line. Insert the bottle back into the bottle support. Screw the soap tank back into the pump assembly. Make sure the tank is firmly secured into place. -
Page 10: Remote Control Functions
REMOTE CONTROL FUNCTIONS If available, the foam dispenser remote control can adjust the dispenser’s settings. To use the remote control hold it in front of the sensor at a distance of 10-15cm (4-6”). Attention: The remote control will not operate out of the recommended range (too close or too far). -
Page 11: Maintenance
M A I N T E N A N C E Care and cleaning of chrome and special finishes DO NOT use steel wool or cleansing agents containing alcohol, acid, abrasives, or the like.Use of any prohibited cleaning or maintenance products or substances could damage the surface of the soap dispenser. -
Page 12: Limited Warranty
If a defect is found in normal use, SUPRATECH will, at its discretion, repair, provide a replacement part or product, or make appropriate adjustments. Damage caused by accident, misuse, or abuse is not covered by this warranty. -
Page 13: Spare Parts List
S PA R E PA R T S L I S T Seals & Screws Kit Elite Foam S07210162 Sensor Kit Elite Foam S07220331 Soap Dispenser Pump S07222028 Pump + Compressor Kit S07222037 Soap Bottle 1 L S07100035 Soap Bottle 1 L Support Kit S07100037 Foam Filter S07212015... -
Page 14: Troubleshooting
T R O U B L E S H O O T I N G PROBLÈME INDICATEUR CAUSE SOLUTION Soap has run low or is completely Refill the soap tank. out. Refer to page 9 Press the refill button located The soap tank has been filled, but at the bottom of the pump to soap has not reached the spout. - Page 15 T R O U B L E S H O O T I N G PROBLÈME INDICATEUR CAUSE SOLUTION Foam coming The connectors between the pump Connect the connectors out of the spout and the electronic unit are not properly so that the white does not stop connected properly.
- Page 16 2, rue des Cyprès - 37240 Bossée - France Tél : (33)2 47 92 23 31 - Fax : (33)2 47 92 84 71 - info@autosanit.com www.autosanit.com 05.21...
Need help?
Do you have a question about the ASKA FOAM and is the answer not in the manual?
Questions and answers