Cooper Tools Quackenbush 140QGDA-RA-SU-MS Operation & Service Manual

Right angle drills

Advertisement

Quick Links

140QGDA-RA-SU-MS &
140QDA-RA-SU-MS
RIGHT ANGLE DRILLS
For additional product information visit our website at www.coopertools.com
N O R T H A M E R I C A
CooperTools
P.O. Box 1410
Lexington, SC 29071-1410
Operation & Service Manual
823220
E U R O P E
Recoules Operation
Zone Industrielle - B.P.28
Avenue Maurice Chevalier
77831 Ozoir-la-Ferriere Cedex, France
11/24/03
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Quackenbush 140QGDA-RA-SU-MS and is the answer not in the manual?

Questions and answers

Summary of Contents for Cooper Tools Quackenbush 140QGDA-RA-SU-MS

  • Page 1 Operation & Service Manual 823220 11/24/03 140QGDA-RA-SU-MS & 140QDA-RA-SU-MS RIGHT ANGLE DRILLS For additional product information visit our website at www.coopertools.com N O R T H A M E R I C A E U R O P E Recoules Operation CooperTools Zone Industrielle - B.P.28 P.O.
  • Page 2: Safety Recommendations

    Safety Recommendations For your safety and the safety of others, read and understand CAUTION the safety recommendations and operating instructions. Always wear protective equipment: • Quackenbush drills are designed to operate on 90psig (6.2 bar) air pressure. Excessive air pressure can increase the loads and stresses on tool parts and drills, and may result in breakage.
  • Page 3 Safety Recommendations Some individuals are susceptible to disorders of the hands and arms CAUTION when exposed to tasks which involve repetitive work motions. Those individuals predisposed to vasculatory or circulatory problems may The spindle on right angle positive feed drills retracts at a much be particularly susceptible.
  • Page 4: Air Supply

    MAJOR TOOL CONTROLS ~2-19/32 (66 MM) ~21/32 (17 MM) ~1-11/16 ~1-13/32 (43 MM) (36 MM) & 380 RPM ~18-21/32 -FOR 1000 RPM, 580 RPM (474 MM) ~5-3/8 -FOR 260 RPM, 200 RPM, 150 RPM 19 7/8 & 95 RPM (137 MM) (505 MM) ~2-19/32 (66 MM)
  • Page 5: Depth Adjustment

    OPERATING INSTRUCTIONS 5. With air supply on, fully depress the rapid advance lever 2. Motor should runs and spindle feed gear (threaded I.D.) must not rotate. Spindle drive gear (splined l.D.) rotates. If the motor If the tool has been shipped recently, been in storage, or runs and the splined ID does not rotate, verify that the shear pin repaired or disassembled;...
  • Page 6 LOCATING EXCESSIVE LEAKAGE IN THE A.C.S. 2. Packed chips or dull cutter may overload the spindle. Feed Most air leaks create a hissing noise that is easily heard if rate may be too high. Drilling or reaming may be beyond the background noise is not too loud.
  • Page 7 DISASSEMBLY—RAPID ADVANCE CLUTCH: Firmly clamp the gear case in a vise. Use a pin spanner wrench to turn the positioning ring 629307 and a appropriate wrench to turn the clutch housing 629602. NOTE: The positioning ring has right hand threads and the clutch housing has left hand threads.
  • Page 8: Final Reduction Assembly

    Unscrew end cap 382668 and spring 382489. Push out throttle Install the drill button and shaft assembly 381171, using a piston 382677. Screw a 1/4-20 cap screw into the metering thread retaining compound. Install the drill button spring 622833 seat 382491. Clamp the cap screw in the vise and use a soft and plug 864387 with O-ring.
  • Page 9 POWER UNIT REASSEMBLY: Slide the motor housing 629319 over the motor. Align the pin Apply a thin film of grease to both sides of gasket 382492. in the motor housing to the hole in the governor housing. Clamp Assemble handle subassembly to governor housing subas- the motor housing to the governor housing using clamp nut sembly with the gasket between.
  • Page 10: Final Assembly

    Install bearing 617980 and two retaining rings 619016 into Install retaining ring 629387 in the large bore of the housing. idler gear 622948. Slip the idler gear on the idler gear post. Align the gap in the retaining ring towards the gear stop. Slide idler gear spacer 629351 onto the idler gear post.
  • Page 11 RIGHT ANGLE HEAD ADJUST SET SCREW IN ITEM 27 SO THAT THESE TWO SURFACES ARE FLUSH. SCALE...
  • Page 12 RIGHT ANGLE HEAD SECTION SECTION...
  • Page 13 RIGHT ANGLE HEAD...
  • Page 14 PARTS LIST FOR RIGHT ANGLE HEAD TABEL 1 ITEM PART NO. PART NAME QTY. SUBASSEMBLY SPINDLE DIFFERENTAL NO. OF FEED RATE/ 629384 HOUSING, RIGHT ANGLE HEAD FEED GEAR FEED GEAR SPACERS RETRACT THRUST PART NO. 631956 629347 629361 .0005 I.P.R./LOW THRUST 629387 RING, RETAINING (1-3/16 UR SERIES) 631942...
  • Page 15 RIGHT ANGLE CLUTCH - 631928...
  • Page 16 RIGHT ANGLE POWER UNIT GEAR TRAINS 1100 844774 1100 864376 1740 844774 GOVERNED TOOLS 1740 864340 3000 846520 POWER UNIT RPM SPINDLE RPM 3000 864237 1100 NONE 1740 NONE 3000 864239 1100 843615 1100 843589 1100 844799 1740 843615 1740 1740 844799 3000 617699 3000...
  • Page 17 RIGHT ANGLE MOTOR & HOUSING Power Unit RPM 629337 629326 629336 629326 1100 629337 865663 1740 629326 867388 3000 629326 864235 812164 4200 Non-Gov 629326 865686 869260 864821 867084 629329 867086 864821 843913 847095 629327 844772 865663 629324 629325 625577 867388 842733 Non-Governed...
  • Page 18 RIGHT ANGLE GOVENOR HOUSING - 631933...
  • Page 19 RIGHT ANGLE BACKHEAD - 631934...
  • Page 20 SPINDLE GUARDS 140 RIGHT ANGLE DRILLS SOLID SPINDLE GUARDS Part No. Name of Part Qty. 624339 Spindle Guard 1" 624340 Spindle Guard 2" 624341 Spindle Guard 3" 624095 Spindle Guard 4" 624342 Spindle Guard 5" Spindle Guard Caps 624355 are included with Spindle Guards. FLUID SPINDLE GUARDS Part No.
  • Page 21 140 RIGHT ANGLE DRILL AIR DIAGRAM...
  • Page 22 NOTES...
  • Page 23 NOTES...
  • Page 24 CooperTools 7007 Pinemont Houston, Texas 77040 Phone: (713) 462-4521 Fax: (713) 460-7008 www.cooperindustries.com...

This manual is also suitable for:

Quackenbush 140qda-ra-su-ms

Table of Contents