Advertisement
When using your electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS AND SAFEGUARDS BEFORE USING THIS APPLIANCE.
To reduce the risk of death or injury by electric shock:
To reduce the risk of burns, electrical shock or injury to persons:
For an appliance that has a rechargeable battery:
SAVE THESE INSTRUCTIONS
THIS APPLIANCE IS FOR COMMERCIAL USE ONLY
The foil is for super close cutting and designed to cut hair that is 1/32" or shorter.
The foil needs to glide over the skin. Do not press hard against the skin but allow the shaver to work for you. Pressing against the skin too hard can cause damage to the foil.
It is important to use the shaver with a foil and cutter bar assembly that is clean and free of hair and other debris that might affect performance.
The foil and cutter bar assembly are wear out parts. Replacement may vary depending on usage. The foil is micro-thin with precise, raised inner cutting edges around the holes. These raised cutting edges will wear with use which will be indicated if your shaver slows down and the foil seems to get warm.
To ensure continued shaving satisfaction, you should replace the foils often and cutter bar assembly periodically.
CUTTER BARS
Replace cutter bar assembly if damaged. Damage to the foil will result from using a broken or bent cutter bar assembly.
REPLACEMENT FOIL/CUTTER BAR ASSEMBLY
WAHL MODEL NO. 7031-100
Replace foil if creased, worn or broken. Using a damaged or broken foil can result in facial injury.
REPLACEMENT SUPER CLOSE GOLD FOIL
WAHL MODEL NO. 7031-200
Always replace the Foil Guard to protect the delicate dual foil heads when the shaver is not in use.
If you are a first-time electric shaver user, or changing FACE from another brand, there will be a 2-3 week (or less) adjustment period, while your face and beard adapt to the new foil.
During the break-in period of the cutter bar, black residue may be left on the face. It is a harmless combination of whiskers, skin debris and minute particles from the cutter bar, which will wash off easily. This condition will quickly disappear with use.
We suggest that you thoroughly cleanse and completely dry skin prior to shaving. For those times when the beard is longer than 1/32" begin by using a trimmer to cut the beard, then use the shaver to get a close, clean shave.
Begin shaving at the neckline, in short, upwards strokes and then continuing upwards until you have shaved all areas of the beard. The shaver is designed to remove most facial hair and give a close, clean shave that is bump and irritation free.
USING CORD/CORDLESS SHAVERS
If battery power is low, the power cord can attach directly to the unit for continued use as a corded unit.
CORDED OPERATION
RECHARGING OPTIONS
Before the equipment is used for the first time, it should be charged fully.
For recharging information, refer to Shaver Use Recharging Options.
Recommendation: The batteries should only be recharged when the performance of the equipment has deteriorated noticeably.
Switch ON the unit using the ON/OFF switch and, after use, switch it OFF again. When the battery is fully charged, the unit can be used for up to 60 minutes of continuous run.
CLEANING THE FLEX FOIL HEAD AND CUTTER BAR ASSEMBLY
DO NOT DIP OR SOAK the shaver or foils in any type of cleaning solution, disinfectant or oil. To disinfect foils, spray disinfectant directly onto foils and wipe off excess liquid to prevent damage to the foil housing. Excess liquid can deteriorate the unit's plastic components and seep into the motor compartment affecting motor life and performance.
Use a clean cloth (dry or dampened with water).
DO NOT USE bleach, benzene or thinner to clean the unit.
The cord should never be used to pull the shaver. Freedom of movement needs to be maintained. Care should be used to keep the cord untwisted, and undamaged. When stored, the cord should be coiled and placed neatly in a dry place.
NI-CAD BATTERY REPLACEMENT, SHAVER DISPOSAL AND RECYCLING
CONTAINS SEALED, RECHARGEABLE NICKEL-CADMIUM BATTERY. MUST BE RECYCLED OR DISPOSED OF PROPERLY.
The RBRC Battery Recycling Seal on the nickel-cadmium (Ni-Cd) battery contained in this product indicates Wahl is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful life, when taken out of service in the United States or Canada. The RBRC program provides a convenient alternative to placing used Ni-Cd batteries into the trash or the municipal waste stream, which is illegal in some areas. Please call 1-800-8-BATTERY for information on Ni-Cd battery recycling in your area. Wahl's involvement in this program is part of our commitment to preserving our environment and conserving our natural resources.
The battery must be removed from the unit before it is scrapped. The unit must be disconnected from the supply mains when removing the battery. The battery is to be disposed of safely.
The battery is a non-consumer replaceable battery. For battery replacement, send your unit and recharging transformer to Wahl Clipper Corporation for service.
If your cord/cordless shaver does not seem to be operating or charging properly, please check the following:
If you still encounter problems with your unit, send your unit and recharging transformer to Wahl Clipper Corporation with a note explaining the problem.
Wahl Clipper Corporation offers a limited warranty on this product.
Please visit our website for full warranty terms.
For servicing, please ship your product prepaid to:
Wahl Service Center
3001 North Locust Street
Sterling, IL 61081
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the 7388 that isn't answered in the manual? Leave your question here.