Related Manuals for Salzburger Getreidemühlen MT 18 D
Summary of Contents for Salzburger Getreidemühlen MT 18 D
- Page 1 SALZBURG GRAIN MILL Instruction manual Please read the operating instructions and safety instructions carefully before using the device for the first time!
-
Page 2: Table Of Contents
Content Operating elements of the MT 18 D electric grain mill ........5 Important information on the operation of the MT 18D mill ......5 Before you grind for the first time ..............7 Basic rules for more safety ................8 Intended use ...................... - Page 3 If all this does not help ..................21 Warranty ....................... 22 Warranty conditions ..................... 22 Warranty processing ..................... 23 Before returning the device ................. 23 Shipping - Packing ....................23 Warrantor and warranty address ..............24 Technical data: MT 18 D ................. 25 Recipes ......................26...
- Page 4 For the love of nature... Dear Customer, We are pleased that you have decided to purchase the Salzburger Grain Mill MT 18 D and would like to wish you a healthy success with your wholefood dishes in advance. With your grain mill, you have purchased a high-quality device that has been built according to our decades of experience.
-
Page 5: Operating Elements Of The Mt 18 D Electric Grain Mill
Operating elements of the MT 18 D electric grain mill Cover Filling funnel Marking grinding degree Thread adjustment Fixing screw 380V Flour ejection mains connection cable, on-off Housing switch Please read the operating instructions and safety instructions carefully before commissioning the device. -
Page 6: Important Information On The Operation Of The Mt 18D Mill
Important information on the operation of the MT 18D mill Controls: Instead of the on/off switch, the MT 18 D mill has a motor protection switch with 380-volt connection with 16-amp CEE plug. The switch is located on the plug. IMPORTANT NOTICE: When using the mill for the first time, the DIRECTION of the lower millstone must be checked. -
Page 7: Before You Grind For The First Time
Before you grind the first time ... No miller has yet fallen from the sky! Before you start grinding, we would like to give you some hints about the natural stone - granite installed in your mill. Our natural stone, unlike artificial grinding stones made of corundum ceramic, is relatively smooth and sensitive to wet grain. -
Page 8: Basic Rules For More Safety
Basic rules for more safety Important safety instructions Please read these operating instructions and safety instructions carefully before operating your grain mill. This will help you avoid mistakes and accidents, and you will use the device safely and functionally. Please keep the instruction manual and pass it on to any user of the product after you. -
Page 9: Intended Use
23. Industrial motors can be damaged by prolonged idling. Therefore, please switch off the mill immediately after use. Intended use The MT 18 D mill is designed and constructed for commercial use. The device is designed for grinding the types of grain listed in the operating instructions and similar. -
Page 10: Quick Guide
Quick guide 1. Insert the mains plug into the socket 2. Place suitable drip tray under flour outlet 3. Turn the thread clockwise until you feel clear resistance 4. Now turn a little counterclockwise until the two red dots are on top of each other. -
Page 11: The Regrind
The ground material Use only cleaned, dried grain! Damp grain smears the millstones! See section "Smudged grinding stones". Poorly cleaned grain may contain foreign bodies (especially small stones, etc.), which may damage the grinding stones. Grind the desired fineness in one pass. Fine milling twice clogs the grain inlet and does not bring the desired success. -
Page 12: Suitable Seeds
Suitable seeds: Seeds Setting Note Wheat, spelt, Any degree of Rye is somewhat more oily and buckwheat, rice, fineness. therefore cannot be ground as rye, barley, millet, finely as spelt and wheat, for green spelt ... example. Corn and soybeans Can be ground. -
Page 13: Store Grain Properly
Store grain properly Since biblical times, it has been known that grain is shelf-stable. This is best given under the following conditions: Humidity below 14%, temperature below 20 °C (temperatures of 5-8 °C are most favorable). If you bought grain, it does not mean that the dryness, which was given when you bought the grain, remains. -
Page 14: Grinding Process
Grinding process Grind the desired fineness in one pass. Grinding twice clogs the grain feed and does not bring the desired s u c c e s s ! The Salzburg Grain Mill grinds powder-fine and flaky flour in just one pass. If there is no grain between the stones, the stones may touch each other at fine setting. -
Page 15: Setting The Fineness
Only looking at the flour outlet and reaching into the flour will really tell you if you are grinding at the correct fineness or need to make a correction. An old baker's rule says: Grind as coarse as possible and as fine as necessary! Operating time: Your mill can grind continuously for several hours. -
Page 16: Change In The Degree Of Fineness
Change of the degree of fineness At a standstill: If there is grain between the grinding stones or in the hopper, no adjustment should be made. The grain, which is still unground between the grinding stones, is jammed. This could cause the mill to have difficulty restarting when it is switched on again. During the meal: You can change from fine to coarse and vice versa during grinding. -
Page 17: Interrupting The Grinding Process
Even if a slight grinding noise of the millstones can be heard, you have closed the funnel too far. Immediately turn the funnel coarser - counterclockwise. Fasten the fixing screw again. The drier the grain, the finer it can be ground, the lower the flour temperature and the better the grinding performance of the grain mill. -
Page 18: Care And Cleaning
Care and cleaning To maintain the technical functionality of your mill, no great effort is required in terms of care and maintenance. All you need to do is make sure that the thread is clean. Cleaning the grinding stones Do not use any liquids! If you use your grain mill regularly, cleaning the millstones is not necessary. -
Page 19: Against Moths And Insects
Against moths and insects Insert a tea bag (herbs) into the flour outlet. Put bay leaves into the grinding chamber. Moths love darkness and quiet and eat only flour, not wood. If you use your mill constantly, moths will not find a cozy place to stay. Cleaning the thread Clean the thread of flour residues using a small brush or paintbrush and a vacuum cleaner. -
Page 20: Problem Solving
Problem solving Problem Cause Solution Mill was adjusted from Set coarser, switch on and only "coarse" to "fine" at then slowly set finer again. standstill while whole grains were still between the grinding surfaces. Motor blocked, Grain is too moist. Grain please dry. -
Page 21: If All This Does Not Help
Problem Cause Solution The device has been Try to open the mill as quickly exposed to excessive as possible even if some force humidity. has to be applied! Then place Funnel can no the mill in a dry place. longer be rotated. -
Page 22: Warranty
Warranty Our grain mills are manufactured and controlled directly at our factory with many years of experience. We use selected materials and motors. Nevertheless, defects may occur. Warranty for commercial mills: 2 years warranty. 12 years warranty on the granite grinding stones. In case of breakage or breakage of stone particles, the stones will be exchanged free of charge. -
Page 23: Warranty Processing
For the assertion of the warranty you need the invoice or the proof of purchase! Warranty processing Repairs of material and workmanship defects within the warranty period will of course be carried out completely free of charge. Before you return the device However, before you send the device to us, we request you to send us a short email or call us. -
Page 24: Warrantor And Warranty Address
Warrantor and warranty address AGRISAN NATURAL PRODUCTS GMBH Gasteigweg 25 A - 5400 Hallein Austria Tel. 0043 6245 83282 E-mail: info@agrisan.at Internet: www.getreidemuehle.com... -
Page 25: Technical Data: Mt 18 D
Technical data: MT 18 D Grinding power fine (wheat): approx. 250/g min. Grinding capacity coarse: a multiple Weight: 20,5 kg Hopper contents: approx. 1.700 g Ø 250 mm Footprint: Height: 470 mm Shelf height: 175 mm Coarse-fine control: stepless Grindstone:... -
Page 26: Recipes
Recipes Spelt brioche 500 g fine spelt flour, 1 pinch of salt, 2 tablespoons of primal sweetener, 1/4l water or soy milk, zest of one lemon, 1 packet of dry yeast, 100 g raisins, 2 tablespoons of health margarine or soy milk. Preparation: Knead the above ingredients into a yeast dough. - Page 28 AGRISAN NATURAL PRODUCTS GMBH Gasteigweg 25 A - 5400 Hallein Austria Tel. 0043 6245 83282 / E-mail: info@agrisan.at Internet: www.getreidemuehle.com www.smoothie-mixer.at www.veganstar.eu https://www.facebook.com/salzburgergetreidemuehlen/...