Related Manuals for Genie Industries Powered Superlift Advantage
Summary of Contents for Genie Industries Powered Superlift Advantage
- Page 1 Technical Publications SUPERLIFT P O W E R E D Operator's Manual First Edition, First Printing Part No. 52035...
-
Page 2: Table Of Contents
This manual E-mail: techpub@genieind.com should be considered a permanent part of your machine and should remain with the machine at all times. If you have any questions, call Genie Industries. Genie Europe Telephone (44) 01636-605030 Fax (44) 01636-611090... -
Page 3: Safety
4 Inspect the workplace. 5 Only use the machine as a material lift. You read, understand and obey: manufacturer's instructions and safety rules–operator's manual and machine decals employer's safety rules and worksite regulations applicable governmental regulations Part No. 52035 Genie Powered Superlift Advantage... - Page 4 Do not use the rotating Do not use blocks to level barrel handler or the machine. vertical barrel stacker with a PSLA-20. Do not move the machine with a raised load, except for minor positioning. Genie Powered Superlift Advantage Part No. 52035...
- Page 5 Bodily Injury Hazards removing the load handling attachments. Do not grasp cable. Do not operate the machine with a hydraulic oil or air leak. An air leak or hydraulic leak can penetrate and/or burn skin. Part No. 52035 Genie Powered Superlift Advantage...
- Page 6 Do not raise the load unless the fork extensions are properly secured to the forks. Never leave a Genie Superlift unattended with a load. Unauthorized personnel may attempt to operate the machine without proper instruction, creating an unsafe condition. Genie Powered Superlift Advantage Part No. 52035...
- Page 7 Do not disconnect charger DC output wires from battery when charger is on. Yellow—used to indicate the presence of a hazard that will or may cause serious injury or damage to the machine. Green—used to indicate operation or maintenance information. Part No. 52035 Genie Powered Superlift Advantage...
-
Page 8: Legend
Mast 16 Up button 25 Fork mounting Loading wheels 17 Down button bracket Emergency Stop button 18 Leg swivel caster 26 Fork extension Loading wheel adjustment 19 Leg 27 Fork extension retaining pin Genie Powered Superlift Advantage Part No. 52035... - Page 9 First Edition Operator's Manual LEGEND Standard Forks Adjustable Forks Flat Forks Boom Part No. 52035 Genie Powered Superlift Advantage...
-
Page 10: Pre-Operation Inspection
Scheduled maintenance inspections shall be performed by qualified service technicians, according to the manufacturer's specifications and the requirements listed in the responsibilities manuals. Genie Powered Superlift Advantage Part No. 52035... - Page 11 Be sure that all structural and other critical components are present and all associated fasteners and pins are in place and properly tightened. o Inspect and clean battery terminals and all battery cable connections. Part No. 52035 Genie Powered Superlift Advantage...
-
Page 12: Function Tests
3 Always perform function tests prior to use. Know and understand the above principle before going on to the next section. 4 Inspect the work place. 5 Only use the machine as a material lift. Genie Powered Superlift Advantage Part No. 52035... - Page 13 5 Repeat steps 1-4 for the other arm. 1 Place the forks inside the carriage. 2 Insert the retaining pin. 3 Adjust the forks to the desired width and be sure the snap pins are properly inserted in each fork. Part No. 52035 Genie Powered Superlift Advantage...
- Page 14 Result: The carriage should lower. properly inserted in each fork. Standard Boom 1 Place the boom inside the carriage. 2 Insert the retaining pin. 3 Attach the lifting shackle to the desired hole on the boom. Genie Powered Superlift Advantage Part No. 52035...
-
Page 15: Workplace Inspection
It is the operator's responsibility to read and remember the work place hazards, then watch for and avoid them while moving, setting up and operating the machine. Part No. 52035 Genie Powered Superlift Advantage... -
Page 16: Operating Instructions
3 Adjust the straddle base to the desired width. 4 Pull out the red Emergency Stop button to the position. 5 Push in the up or down button on the hand controls for the desired direction of travel. Genie Powered Superlift Advantage Part No. 52035... - Page 17 After Each Use To prepare Genie Superlift for storage, follow setup procedure in reverse order. Select a safe storage location - firm level surface, weather protected, clear of obstruction and traffic. Charge the batteries. Part No. 52035 Genie Powered Superlift Advantage...
- Page 18 7 Set the power switch to the position. AUTO 8 Monitor the ampere meter for the correct charge rate. The initial charge rate should be approximately 10A. The charge rate will decrease as the battery reaches full charge. Genie Powered Superlift Advantage Part No. 52035...
-
Page 19: Load Capacity Charts
See chart on page 18 for maximum load centers for standard forks, adjustable forks and flat forks. Part No. 52035 Genie Powered Superlift Advantage... - Page 20 42 in 107 cm measure to the load center 18 in 24 in 32 in 42 in 46 cm 61 cm 81 cm 107 cm Load Capacity Chart Load Center inches Model PSLA-20 Genie Powered Superlift Advantage Part No. 52035...
-
Page 21: Transport Instructions
2 Rotate the carriage hold down bar over the column. carriage. 3 Raise the carriage until it contacts the carriage Always place the lifting hold down bar. hook through the lifting bracket so that it points toward the machine. Part No. 52035 Genie Powered Superlift Advantage... -
Page 22: Decals
Danger - Battery Safety 52054 13 28372 Warning - Crush Hazard Caution - Quick Disconnect 52052 14 37145 Powered Superlift Advantage Logo Label - Manual Lowering Valve 32718 15 32687 Warning - Flat Forks Safety Warning - Standard Forks Safety & Setup 33468... - Page 23 First Edition Operator's Manual DECALS Shading indicates that decal is hidden from view. Part No. 52035 Genie Powered Superlift Advantage...
- Page 24 Operator's Manual First Edition DECALS Genie Powered Superlift Advantage Part No. 52035...
-
Page 25: Specifications
11.5 cm 4.5 kg Load Platform 26.5 lbs 70 cm 60 cm 6.5 cm 12.0 kg Fork extensions (each) 30 in 2 in 3 in 76 cm 5 cm 8 cm 2 kg Part No. 52035 Genie Powered Superlift Advantage... - Page 26 Distributed By: Genie North America Genie Japan Genie Holland Genie Germany Phone: 425-881-1800 Phone: 81 3 3453 6082 Phone: 31 70 51 78836 Phone: 49 4202 8852-0 Fax: 425-883-3475 Fax: 81 3 3453 6083 Fax: 31 70 51 13993 Fax: 49 4202 8852-20 Toll Free in US &...
Need help?
Do you have a question about the Powered Superlift Advantage and is the answer not in the manual?
Questions and answers