Related Manuals for Daewoo DAFR70
Summary of Contents for Daewoo DAFR70
- Page 1 DAFR70 Scrubber dryer on seat USER'S MANUAL www.daewoopowerproducts.com Manufactured under license of Daewoo International Corporation, Korea...
-
Page 2: Table Of Contents
INDEX 1. ON CONSIGNMENT OF THE MACHINE ....................1 2. SERIAL NUMBER PLATE......................... 8 3. INTRODUCTORY COMMENT........................9 4. INTENDED USE............................10 5. SYMBOLS USED ON THE MACHINE....................14 6. GENERAL SAFETY REGULATIONS......................17 7. MACHINE PREPARATION........................18 8. TECHNICAL DATA..........................24 9. EXPLODED VIEW..........................24 WARRANTY ..............................30... -
Page 3: On Consignment Of The Machine
SYMBOLS USED IN THE MANUAL Open book symbol with an "i" Indicates the need to consult the instruction manual Open book symbol Used to tell the operator to read the manual before using the machine Warning symbol Carefully read the sections marked with this symbol and observe the indications, for the safety of the operator and the machine Warning symbol Indicates danger of gas exhalation and leakage of corrosive liquids... -
Page 4: Intended Use
available for advice or direct intervention. Intended use The scrubbing machine is designed exclusively for the professional cleaning of surfaces and floors in industrial, commercial and public environments. The machine is only suitable for use in closed - or at least covered - locations. - Page 5 immediately if they become damaged. -The machine must be exclusively used by authorised, trained personnel. -Do not use the machine on surfaces with an inclination greater than the one shown on the plate. -The machine is not suitable for cleaning rough or uneven floors. Do not use the machine on slopes. -If the power supply cable of the battery charger is damaged, contact an Authorised service centre immediately.
-
Page 6: Machine Preparation
-Do not remove the guards that can only be removed with the aid of tools, except for maintenance work (see the relevant paragraphs) -Do not wash the machine with direct water jets or with pressurised water, nor with corrosive subs- tances. - Page 7 ATTENTION: if the product is delivered in cardboard containers, handle the packed product with suitable lifting means that comply with the legal requirements WARNING: During this operation, check there are no people or objects near the machine 2. HOW TO MOVE THE MACHINE 1.
- Page 8 11. Main key switch 5. FOOTBOARD ELEMENTS The components on the front right part of the foot board are: 12. Drive pedal 13. Emergency button 14. Detergent solution level tube 15. Recovery tank release button 6. SIDE MACHINE ELEMENTS The elements on the left-hand side of the machine are: 16.
- Page 9 8. FRONT MACHINE ELEMENTS The elements on the front of the machine are: 25. Detergent solution filter 26. Detergent tank drainage tap 9. TYPE OF BATTER To power the machine it is necessary to use: -liquid-electrolyte lead traction batteries -sealed traction batteries with gas recombination or gel technology. OTHER TYPES MUST NOT BE USED.
- Page 10 DEAD BATTERIES ARE CLASSIFIED AS DANGEROUS WASTE AND MUST BE DELIVERED TO THE AUTHORISED BODIES FOR CORRECT DISPOSAL. WARNING: You are advised to always wear protective gloves, to avoid the risk of serious injury to your hands. WARNING: You are advised to only lift and move the batteries with lifting and transportation means suitable for the specific weight and size 11.HANDLING - INSERTING BATTERIES The batteries must be housed in the special compartment beneath the seat carter.
- Page 11 4.Grip the recovery tank and rotate it as far as it will go ATTENTION: You are advised to only lift and move the batteries with lifting and transporta tion means suitable for the specific weight and size 5.House the batteries in the compartment, positioning the poles “+”and “-”opposite each other 12.BATTERY CONNECTION AND BATTERY CONNECTORS 1.Connect the batteries in series to the "+"...
- Page 12 fumes to escape 10. After the charging cycle is complete, the battery connector must be connected to the machine connector WARNING: Danger of gas exhalation and leakage of corrosive liquids. WARNING: Danger of fire: do not go near with free flames 14.FORWARD WORK SPEED This machine is equipped with electronic traction control.
- Page 13 16.FILLING THE SOLUTION TANK The solution tank can be filled in two different ways: 1.removing the inlet cap (1) and filling with the aid of a rubber tube 2.using the rubber cap (2); this supports the water hose on its own, but be sure to remove the inlet (1) to allow the proper vent of air.
- Page 14 5.(2), making sure the washer and spring adhere in the upper part of the squeegee support 6.knob (3), making sure the washer and spring adhere in the upper part of the squeegee support 7.Insert the suction hose (4) in the squeegee sleeve ATTENTION: these operations must be carried out using protective gloves to avoid any possible contact with the edges or tips of metal objects.
- Page 15 11.Lower the brush head by turning the right level(6)clockwise, then lower the squeegee turning the left lever (7) anticlockwise. WARNING: As soon as the forward movement pedal is activated with the brush head in its work position, the solenoid valve will start working and will begin dispensing detergent solution. As soon as the squeegee is in its work position, the vacuum motor will switch on and being working.
- Page 16 recovery tank through the special drainage pipe (1). 23.EMERGENCY BUTTON If there are any problems while you are working, press the emergency button (1) beneath the seat. This command interrupts the electric circuit between the batteries and the machine system, so the machine stops and the electric brake is triggered.
- Page 17 WARNING: Before performing any maintenance, remove the keys from the panel and disconnect the battery connector of the machine. 4.Disconnect the tube (4) from its seat, unscrew the drainage cap and empty the recovery tank. WARNING:This operation must be carried out using gloves to protect against contact with dangerous solutions.
- Page 18 DAILY MAINTENANCE PERFORM ALL MAINTENANCEOPERATIONS IN SEQUENCE 25.CLEANING THE RECOVERY TANK 1. Disconnect the tube (1) from its seat, unscrew the drainage cap and empty the recovery tank. 2. Press the button (1) to release and rotate the recovery tank WARNING: Before performing any maintenance, remove the keys from the panel and disconnect the battery connector of the machine.
- Page 19 27.CLEANING THE SQUEEGEE The careful cleaning of the whole vacuum unit ensures better drying and cleaning of the floor as well as greater duration of the suction motor. Proceed as follows for cleaning: 1.Slide the suction tube (1) from the squeegee sleeve. 2.Remove the squeegee (2) from the support arm by unscrewing the hand wheel (3).
- Page 20 2.Open the filler cap (1) WARNING: before performing any maintenance, remove the keys from the panel and disconnect the battery connector WARNING: these operations must be carried out using gloves to protect against contact with dangerous solutions. 3.Close the water tap by shifting the relevant knob (on the left part of the steering column) upwards 4.Loosen the filter cap (2) on the front of the machine 5.Remove the internal filter cartridge and rinse everything thoroughly with running water 6.Reassemble all the elements...
- Page 21 3. Press the brush release button (2) on the steering wheel 4.As soon as the button is pressed, you will see the question “RELEASE” on the screen 5.Press the brush release button (2) on the steering wheel again, to confirm WARNING :During this operation, check there are no people or objects near the brush.
- Page 22 1.Check the state of wear and tear of the brushes and, if necessary, replace them. The brushes should be changed when the bristles are about 15 mm long. To replace them, see “REPLACING THE BRUSHES”, or “DISASSEMBLING THE BRUSHES”and “ASSEMBLING THE BRUSHES”. Working with over-worn brushes may cause damage to the floor.
- Page 23 CHOOSING AND USING THE BRUSHES POLYPROPYLENE BRUSH (PPL) Used on all types of floors. Good resistance to wear and tear, and hot water (no greater than 60 . The Polypropylene brush is non-hygroscopic and therefore retains its characteristics even when working in wet conditions.
-
Page 24: Technical Data
8. TECHNICAL DATA Working width: mm 560 Squeegee width: mm 800 Working capacity: 3500 ㎡/ h Disc brush: No. / Ø mm 1 / 560 Disc brush rotations RPM 200 Brush motor V/W 24/550 Maximum pressure on the brushes KG Traction motor: 24/500 V/W Traction wheel (number / diameter / width) No. -
Page 25: Exploded View
10. EXPLODED VIEW MDSOFT Parts Parts Number Brush plate cover 70010301 Brush holder 70010302 Brush retainer 70010303 spring Spring press plate 70010304 for brush retainer Hexagon bolt 70010305 M6X10 21 inch brush 70010306 Round head square 70010307 neck bolt M8X20 hexagon socket countersunk 70010308 head bolts M6X16... - Page 26 Parts Parts Number Clear water 700201 tank Clear Water tank 700202 back Cross self-tapping 700203 bolt M5X12 cushion 700204 sewage tank 700205 buckles M6 flat gasket 700206 Hexagon socket 700207 bolt M5X12 M8 flat gasket 700208 Hexagon socket 700209 bolt M6X30 foot accelerator 700210 foot rest...
- Page 27 Parts Parts Number Plastic cover for MDSOFT 70010601 directional column Plastic gasket 70010602 Cross countersunk 70010603 head bolt M5X16 Display board 70010604 sticker Steering wheel 70010605 top cover transparency cover 70010906 display panel 70010607 Cross tapping screw 70010608 M3X8 Steering wheel 70010609 fixed base plate Steering wheel...
- Page 28 MDSOFT Parts Parts Number Sewage tank 700301 Sewage tank 700302 cover Seal ring for 700303 sewage tank cover Float barrel 700304 holder Float barrel 700305 retaining ring Float barrel 700306 Floating ball barrel 700307 bracket seal ring Cross large pan 700308 head bolt M6X11 Sewage tank...
- Page 29 MDSOFT Parts Parts Number frame body 7001 Tank cleaning mechanism 7002 Sewage tank mechanism 7003 battery tray 7004 battery 7005 70 Vehicle structure drawing...
- Page 30 EC DECLARATION OF CONFORMITY Model Name: Scrubber dryer on seat Model Code: DAFR70 Brand: Daewoo We GBR Corp. LTD, Room 1002, 10/F., David House, 8-20 Nanking Street, Jordan, Kowloon, Hong Kong, China, declare under our sole responsibility that this product is in conformity and accordance with the following standards and regulations.
-
Page 31: Warranty
WARRANTY CARD Product model Date of sale Company Serial number Client's signature Username The product is in good conditions and fully complete. Read and agree the terms of the warranty. GUARANTEE The warranty period starts from the date of sale of the products and covers 2 years for all power products. During the warranty period, free failures caused due to the use of poor-quality materials in the production and manufacturer workmanship admitted fault are removed. - Page 32 Manufactured under license of Daewoo International Corporation, Korea...
Need help?
Do you have a question about the DAFR70 and is the answer not in the manual?
Questions and answers