Table of Contents
Advertisement
TRx3210A Active Module and Settings
The active TRx3210A triamp module is driven by X-Drive™ DSP processing with optimized presets for arrays and ground stacks.
Crossover filters, Parametric EQ, Alignment Delay and Amp Limiters are factory tuned to maximize performance output.
POWER SWITCH
Push the upper portion of the power switch to turn the system on. If the
blue POWER indicator is on but there is no sound check the Protect LED.
POWER LED
The POWER LED indicates the unit is turned on and functioning properly.
SIGNAL LED
The SIGNAL LED indicates there is a signal present at the INPUT XLR.
LIMIT LED
The LIMIT LED indicates maximum output of the system is being
reached. A flashing LIMIT LED is acceptable. The DSP will reduce peaks
to prevent amp clipping. If the LIMIT LED is continuously ON, reduce
the level going in to the INPUT XLR. As with any system, reduce the
volume if distortion is heard.
PROTECT LED
The PROTECT LED indicates one of the protection circuits has activated.
To reset the amp, turn the power off for about 10 seconds, then turn it
back ON. If the PROTECT LED stays lit for more than 5 seconds, check
for a blocked fan intake.
DIGITAL DISPLAY
The bright green LED DIGITAL DISPLAY will display various information
about the system and its settings. When you first turn on the unit, the
display will indicate which preset is loaded.
SETTING BUTTONS: UP/DOWN (SET) & LEFT/RIGHT
Use the UP and DOWN (SET) buttons to load presets for different
speaker configurations, based on the number of TRx3210A and the
array angle set by the SureFly™TRx quick release pins.
1-4 boxes
0-2.5 deg (straight)
1-4 boxes
5-7.5 deg
1-4 boxes
10 deg
5-8 boxes
0-2.5 deg (straight)
9-12 boxes
0-2.5 deg (straight)
13-16 boxes
0-2.5 deg (straight)
Use the LEFT/RIGHT buttons to access the Input Sensitivity setting and
set with the UP/DOWN for 1.0 Vrms, 1.2Vrms, 1.4Vrms or 2.0 Vrms.
The factory setting is 1.4Vrms. Increase the setting to lower the output.
USB PORT
The USB port is for updating system firmware such as additional presets.
REMOTE LEVEL (MUTE) CONNECTOR
This is a terminal block connector with 5 volt control of volume, typically
used in permanent installations. Short the CTL and GND pins to MUTE.
INPUT/THRU XLR CONNECTORS
Connect the INPUT XLR to a signal source such as the output of a mixer.
The THRU XLR can be connected to more TRx3210A's or other units.
FAN INTAKE/EXHAUST VENTS
The TRx3210A features a variable speed fan, which runs silent at low
speeds. Make sure the fan intake and exhaust vents are free from
blockage at all times.
AC IN JACK (BLUE PowerCon™ A-type)
The AC IN connector accepts the blue Neutrik™ PowerCon™ "A-type"
connector (part# NAC3FCA). One NAC3FCA connector is supplied,
attached to a short length of 3-conductor wire. You can use a longer
wire if it is properly rated for the application. Attach a proper 3-prong
connector for your voltage type to the other end of the wire, with
careful attention to follow the correct pinouts and safety standards.
No attempt should ever be made to use the unit without the ground
connected. Plug into the proper voltage for your unit.
Alternately, you can attach the grey Neutrik™ PowerCon™ "B-type"
connector (part# NAC3FCB) for an A-B jumper cable between two
TRx3210's. Pay careful attention
to follow the correct pinouts and
safety standards. With the con-
nector attached, plug into the AC
OUT jack of another TRx3210A, or
into a PowerCon™ "B-type" outlet
with the proper voltage.
AC OUT JACK (GREY PowerCon™ B-type)
The AC OUT connector accepts the grey Neutrik™ PowerCon™
"B-type" connector (part# NAC3FCB), and is used to power other
units.
Use the VA rating on other devices to determine how many can be
connected to the AC OUT. The maximum limit on the AC OUT connec-
tor is 15A. Other limiting factors include the breaker rating for the AC
line you are plugging into, wire type and (if used) generator capacity.
FUSE
The FUSE is located internally near the AC input. To check or replace,
first remove the power cord and then remove the amp module from
the speaker enclosure then remove the front panel to access the fuse.
The fuse type is a 250V Slow Blow rated at 10A.
PowerCon™ wiring
N
L
15
Advertisement
Table of Contents
