Multi-Split Type Air Conditioner - Fujitsu ASYG09KGTE Operation Manual

Temporary deactivation of wireless LAN
NOTE: If you do not press any buttons of the remote controller for 60
seconds, the remote controller display will return to the original
display.
1. Press on the remote controller until
only the clock is displayed on the remote
controller display.
2. Press and hold
controller for more than 5 seconds.
will be displayed on the remote controller
display.
3. Select using
4. Press
.
[ ] indicator on the indoor unit will turn off.
* If you want to activate wireless LAN again, select
Initialization (reset)
Initialize (reset) this product in the following situations:
• Changing the access point
• Disposing this product
• Transferring this product to a third party
Unregister the air conditioner
Unregister the air conditioner by using the mobile app. (Refer to the
operation manual of the mobile app for details.)
Initialization of the WLAN adapter
NOTE: If you do not press any buttons of the remote controller for 60
seconds, the remote controller display will return to the original
display.
1. Press on the remote controller until
only the clock is displayed on the remote
controller display.
2. Press and hold
controller for more than 5 seconds.
will be displayed on the remote controller
display.
3. Select using
4. Press .
on the remote controller display will blink.
5. Press .
[ ] indicator on the indoor unit will turn off after blinking fast.
To continue use
If you or third party wishes to continue the use of the product, follow the
procedures in "Air conditioner registration (pairing of WLAN adapter)" to
reconnect to a different access point.
NOTE: Wireless LAN setup is not possible if the previous owner did not
unregister or initialize this product. In this case, contact your
authorized service personnel.
En-13
on the remote
. *
in step 2.
on the remote
.

12.3. Multi-split type air conditioner

This indoor unit can be connected to a multi-split type outdoor
unit. The multi-split type air conditioner allows multiple indoor
units to be operated in multiple locations. The indoor units may
be operated simultaneously, in accordance with their respective
output.
Simultaneous Use of Multiple Units
● When using a multi-split type air conditioner, the multiple indoor units
can be operated simultaneously, but when 2 or more indoor units of
the same group are operated simultaneously, the heating and cooling
efficiency will be less than when a single indoor unit is used alone.
Accordingly, when you wish to use more than 1 indoor unit for cooling
at the same time, the use should be concentrated at night and other
times when less output is required. In the same way, when multiple
units are used simultaneously for heating, it is recommended that they
be used in conjunction with other auxiliary space heaters, as required.
● Seasonal and outdoor temperature conditions, the structure of
the rooms and the number of persons present may also result in
differences of operating efficiency. We recommend that you try various
operating patterns in order to confirm the level of heating and cooling
output provided by your units, and use the units in the way that best
matches your family's lifestyle.
● If you discover that 1 or more units delivers a low level of cooling or
heating during simultaneous operation, we recommend that you stop
simultaneous operation of the multiple units.
● Operation cannot be done in the following different operating modes.
If the indoor unit is instructed to do an operating mode that it cannot
perform, [ ] indicator on the indoor unit blinks (1 second on, 1 second
off) and the unit goes into the standby mode.
Heating mode and Cooling mode (or Dry mode)
Heating mode and Fan mode
● Operation can be done in the following different operating modes.
Cooling mode and Dry mode
Cooling mode and Fan mode
Dry mode and Fan mode
● The operating mode (Heating mode or Cooling (Dry) mode) of the out-
door unit will be determined by the operating mode of the indoor unit
that was operated first. If the indoor unit was started in the Fan mode,
the operating mode of the outdoor unit will not be determined.
For example, if indoor unit (A) was started in the Fan mode and then
indoor unit (B) was then operated in the Heating mode, indoor unit (A)
would temporarily start operation in the Fan mode but when indoor
unit (B) started operating in the Heating mode, [ ] indicator for indoor
unit (A) would begin to blink (1 second on, 1 second off) and it would
go into standby mode. Indoor unit (B) would continue to operate in
Heating mode.