Table of Contents
Advertisement
Quick Links
PRODUCT
The RM-iC series readers provide an enclosed RM-4 board and attached iCLASS read
head, available in the following styles:
OVERVIEW
The RM-iC Quick Start Installation Guide provides a synopsis of installation and
connection information for RM-iC series readers. Refer to the RM-4/RM-4E Technical
Manual for in-depth technical and installation information.
Specifications
The following specifications apply to all RM-iC series readers:
NOTE
Standards
RM-iC series readers are Underwriters Laboratories Inc. (UL), Listed to Standard UL
294, Access Control System Units, Fifth Edition. RM-iC series readers must be wired in
accordance with the National Electrical Code (ANSI/NFPA 70), local codes, and the
authorities having jurisdiction.
RM1-iC - enclosed RM-4 and attached iCLASS read head
RM2-iC - enclosed RM-4 with keypad and attached iCLASS read head
RM2L-iC - enclosed RM-4 with keypad, LCD display, and attached iCLASS read
head.
Power: 12VDC, 300 mA
Cable: Beldon 9841
Cable distance from iSTAR or apC: 4,000 ft
Temperature
Indoor: 32° F to 120° F (0° C to 49° C)
Outdoor: -31° F to 151 ° F (-35 ° C to 66° C)
Qualified on 26-bit, 35-bit, 37-bit, and 32-bit Mifare serial number formats.
UL has only evaluated the 26-bit HID card format for this unit.
RM-iC Series
Quick Start
Installation Guide
Part Number UM-068
Version D0
July 2005
1
Advertisement
Table of Contents
Related Manuals for Software House RM-iC Series
Summary of Contents for Software House RM-iC Series
- Page 1 Standards RM-iC series readers are Underwriters Laboratories Inc. (UL), Listed to Standard UL 294, Access Control System Units, Fifth Edition. RM-iC series readers must be wired in accordance with the National Electrical Code (ANSI/NFPA 70), local codes, and the authorities having jurisdiction.
-
Page 2: Installation
5. Installing the ARM-1 relay board 6. Installing the heater kit. Installing the Mount Figure 1 shows RM-iC standard housing, mount plate, and gasket. All RM-iC series readers conform to the same housing, mount plate, and gasket dimensions. Plate Standard Housing... -
Page 3: Wiring The Components
Installation This device has been approved for outdoor use when properly installed with RM Heater Kit Installation (P.N. 130-915) and the supplied gasket material. Position the gasket with the RM plate so that the mounting holes are properly aligned. Ensure that the gasket is placed between the mounting surface and mating surface of the RM plate. -
Page 4: Installing The Arm
If the module is not last, SW3, position 5 should be Off (open). Installing the ARM-1 Two ARM-1 relay components can be connected to the RM-iC series reader through the P5 connector (Table 1 ). P5-1 is the common pin for either ARM. P5-2 is the output Relay drive for the first relay. -
Page 5: Installing The Heater
Installation Installing the Heater RM-iC readers require a heater kit (Model 130-915) when installed outdoors in an environment and where temperatures may drop below 40° F (5° C). The Model 130-915 heater kit contains the following parts: TABLE 2. Heater Parts Quantity Description Transformer 12 VAC 40VA... -
Page 6: Installing The Thermostat
Installation Figure 6 shows RM installation FIGURE 6. RM Installation Heater Strip Application To avoid problems such as placing the strips too far away from the thermostat, not allowing the thermostat to shut off, or locating the strips too close to the PWB and causing component over-temperature concerns, follow mounting diagram and heater strip application instructions. - Page 7 Tighten the screws allowing the thermostat to be sufficiently secured to the plate. Do not over tighten the screws. TESTING WITH APC To test an RM-iC series reader with an apC or iSTAR: OR ISTAR 1. Measure the supply voltage to the RM-4.
- Page 8 Testing with iSTAR PRO Hardware TESTING WITH To test an RM-iC series reader with iSTAR Pro, use the iSTAR Pro S4 switch, positions 5 through 8. ISTAR PRO HARDWARE Table 3 shows S4 settings for Positions 5 through 8. TABLE 3. S4 Diagnostic Settings...
-
Page 9: Fcc Digital Device Limitations
Canadian Radio Emissions Requirements CANADIAN RADIO This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian EMISSIONS Department of Communications. REQUIREMENTS Le present appareil numerique n’emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de la class A prescrites dans le Reglement sur le brouillage radiolelectrique edicte par le ministere des Communications du Canada. - Page 10 FCC Digital Device Limitations...
Need help?
Do you have a question about the RM-iC Series and is the answer not in the manual?
Questions and answers