Table of Contents
Advertisement
PROJECTION CONFIGURATION CHANGE
For XG135LC
To change screen size only:
1) Set the focus ring to the proper position.
For 100" screen size
For 120" screen size
R – H-3, V-3
R – H-3.5, V-2.5
G – H-5, V-3
G – H-5, V-2.5
B – H-3, V-3
B – H-3.5, V-2.5
2) Adjust the angle of the CRT's.
For 100" screen size
Move the CRT to the 100 position
To change to the desk top system (front)
1) Reverse the scan.
(See page 14.)
2) Set the focus ring to the proper position.
For 100" screen size
For 120" screen size
R – H-3, V-3
R – H-3.5, V-2.5
G – H-5, V-3
G – H-5, V-2.5
B – H-3, V-3
B – H-3.5, V-2.5
3) Adjust the angle of the CRT's.
For 100" screen size
Move the CRT to the 100 position
4) Select an installation from the PJ ORIENTATION menu in
the SETTING menu. (See "Projection Type Selection" in the
setup manual.)
(See page 17.)
For 180" screen size
R – H-3.5, V-2.5
G – H-5,
V-2.5
B – H-3.5, V-2.5
(See page 18.)
For 120–180" screen size and the
other screen sizes
Move the CRT to the 120, 180, or
60–300 position
(See page 17.)
For 180" screen size
R – H-3.5, V-2.5
G – H-5,
V-2.5
B – H-3.5, V-2.5
(See page 18.)
For 120–180" screen size and the
other screen sizes
Move the CRT to the 120, 180, or
60–300 position
To change to the ceiling mount system (rear)
1) Reverse the scan.
(See page 14.)
2) Set the focus ring to the proper position.
For 100" screen size
R – H-3, V-3
G – H-5, V-3
B – H-3, V-3
3) Adjust the angle of the CRT's.
For 100" screen size
Move the CRT to the 100 position
4) Select an installation from the PJ ORIENTATION menu in
the SETTING menu. (See "Projection Type Selection" in the
setup manual.)
To change to the desk top system (rear, 0 projection angle)
1) Set the focus ring to the proper position.
For 100" screen size
R – H-3, V-1
G – H-5, V-1
B – H-3, V-1
2) Adjust the angle of the CRT's
For 100" screen size
Move the CRT to the 100 position
3) Select an installation from the PJ ORIENTATION menu in
the SETTING menu. (See "Projection Type Selection" in the
setup manual.)
12
(See page 17.)
For 120" screen size
For 180" screen size
R – H-3.5, V-2.5
R – H-3.5, V-2.5
G – H-5,
V-2.5
G – H-5,
B – H-3.5, V-2.5
B – H-3.5, V-2.5
(See page 18.)
For 120–180" screen size
Move the CRT to the 120, or 180.
(See page 17.)
For 120" screen size
For 180" screen size
R – H-3.5, V-1
R – H-3.5, V-1
G – H-5,
V-1
G – H-5,
B – H-3.5, V-1
B – H-3.5, V-1
(See page 18.)
For 120–180" screen size and the
other screen sizes
Move the CRT to the 120, 180, or
60–300 position
V-2.5
V-1
Advertisement
Table of Contents
