Advertisement
Quick Links
RX40A REBAR TIER
OWNER'S MANUAL
Improper and unsafe use of this tool will result in death or serious injury. It is very
important that the intended operator of this tool reads and understands this manual
before operating this tool. Keep this manual available for others before they use the tool.
0508 782 753 |
Freephone
sales@delfast.com
Email
|
@DelfastNZ #Delfast
delfast.com
Advertisement
Related Manuals for Delfast RX40A
Summary of Contents for Delfast RX40A
- Page 1 RX40A REBAR TIER OWNER’S MANUAL Improper and unsafe use of this tool will result in death or serious injury. It is very important that the intended operator of this tool reads and understands this manual before operating this tool. Keep this manual available for others before they use the tool.
-
Page 2: Table Of Contents
Table of Contents Parts Breakdown Safety Safety Lock Product Specification and Technical Parameters Battery and Charger Usage Machine Operation and Methods Employed Common Faults and Removal Methods Care and Maintenance Freephone. 0508 782 753 Email. sales@delfast.com... -
Page 3: Parts Breakdown
Parts Breakdown Front Back Battery Charger delfast.com... -
Page 4: Safety
Safety The RX40A is a high-performance battery-operated tool. Failure to follow the warnings and instructions may result in electrical shock, fire or serious injury. Always operate the tool with personal protective equipment (safety helmet and eye protection). Using the appropriate safety equipment at all times will avoid body injury. -
Page 5: Safety Lock
To ensure safe operation, the machine is equipped with the safety devices as follows: Main Switch Turn the switch on for power supply when in operation. Trigger Lock Always turn the trigger lock to the OFF position when not in use or when changing the coil. delfast.com... - Page 6 Voltage (V) Max. tying dia. (mm) Main technical parameters for tying wire Item Code FW-C10, FW-C30 Diameter (mm) Material Q195 Length (m) 100 (approx.) Corresponding rebar size for RX40A model Longitudinal steel dia. Traverse steel Freephone. 0508 782 753 Email. sales@delfast.com...
-
Page 7: Battery And Charger Usage
This is indicated by the charging light. It will take about 90 minutes to fully charge a battery. It is recommended to charge the battery at 0deg – 45deg. Do not charge under extremely cold or hot environments. delfast.com... -
Page 8: Machine Operation And Methods Employed
Installation of wire coils. Only use Delfast wire coils in your RX40A rebar tool. Using nonstandard wire coils will cause the tool to malfunction. Remove the adhesive tape (if applied) and cut off about 2cm of the head of wire. -
Page 9: Common Faults And Removal Methods
Carry out a daily inspection before sending or getting back the machine; the user must carry out a daily inspection before using. Please maintain your RX40A carefully, check if there is an incorrect adjustment, moveable parts locked, damage to the switch as well as other possible conditions. If so, stop using the machine and repair. - Page 10 (Pos. 328) and route unit (pos 325). Or route PWB unit (pos PWB unit (pos 325). bad connection of 325). Or check the Or replace a new connecting wire K. wire K connection connecting wire K. Freephone. 0508 782 753 Email. sales@delfast.com...
- Page 11 Six short beeps The tool is used at Check the Leave the tool and repeated high temperature. temperature at the the battery pack at (pipipipipipi, job site. normal temperature pipipipipipi) in the room for some time and then continue the operation. delfast.com...
- Page 12 RX40A REBAR TIER OWNER’S MANUAL Improper and unsafe use of this tool will result in death or serious injury. It is very important that the intended operator of this tool reads and understands this manual before operating this tool. Keep this manual available for others before they use the tool.
Need help?
Do you have a question about the RX40A and is the answer not in the manual?
Questions and answers