Related Manuals for HYCON HY17M26 Series
Summary of Contents for HYCON HY17M26 Series
- Page 1 HY17M26 Series IDE Hardware User’s Manual ©2022 HYCON Technology Corp. APD-HY17MIDE010-V02_EN www.hycontek.com...
-
Page 2: Table Of Contents
4. DESCRIPTION OF THE HARDWARE........................7 4.1. Architecture description.............................7 4.2. Control Box Introduction............................7 4.3. Introduction to Target Board............................. 8 4.4. Target Board Circuit Diagram..........................11 4.5. Control Box and Target Board Hardware Connection Steps................12 5. REVISIONS..................................13 ©2022 HYCON Technology Corp APD-HY17MIDE010-V02_EN www.hycontek.com page2... - Page 3 HY17M26 Series IDE Hardware User’s Manual Attention: 1、 HYCON Technology Corp. reserves the right to change the content of this datasheet without further notice. For most up-to-date information, please constantly visit our website: http://www.hycontek.com 2、 HYCON Technology Corp. is not responsible for problems caused by figures or application circuits narrated herein whose related industrial properties belong to third parties.
-
Page 4: Package Contents
Model No. Part Name Description Quantity HY17M26-AM01 HY17M26-NS32 Target Board HY17M00-CM01 HY17M00 Control Box HY17M26-DK01 Cable line USB Type A to Mini B Cable Interface line 5pin/2.54 (2.54mm pitch) Table1-1 ©2022 HYCON Technology Corp APD-HY17MIDE010-V02_EN www.hycontek.com page4... -
Page 5: Safety Precautions
When following status occurred, please remove the power supply immediately, and contact our engineer. Power Supply line is worn or damaged. Power source (battery) connected but no any light on while operating. Component off. ©2022 HYCON Technology Corp APD-HY17MIDE010-V02_EN www.hycontek.com page5... -
Page 6: Software Installation Requirements
(FW version applicable to HY17M00-CM01 is W17M01.9.2 or above) (4) Supported software version: HY17M IDE V2.02 above: HY17M Series Assembly Language IDE software H08 CIDE V1.30 above: HYCON 8-bit MCU C Language IDE software (5) Supported Operating system: Windows XP, Windows Vista, Windows 7, Windows 8, Windows 10... -
Page 7: Description Of The Hardware
Green LED, When the USB Port is connected to a computer or an external 5V power supply, the L1 light indicates that the Control Box is powered. Error Red LED (reserved, no use). Busy Yellow LED (reserved, no use). ©2022 HYCON Technology Corp APD-HY17MIDE010-V02_EN www.hycontek.com page7... -
Page 8: Introduction To Target Board
(Appearance shown in Figure 4-3), this Target Board can be used in addition to IDE hardware tools, It can also be used as a demo board, the following describes the related functions of the Target Board: ©2022 HYCON Technology Corp APD-HY17MIDE010-V02_EN www.hycontek.com page8... - Page 9 Description: Pins are defined as follows Name Description VDD_ICE Target Board Chip’s VDD power is coming from Control Box VDD_IN Target Board Chip’s VDD power Target Board Chip’s VDD power is coming from external VDD_EXT power ©2022 HYCON Technology Corp APD-HY17MIDE010-V02_EN www.hycontek.com page9...
- Page 10 UART’s receive pin UART’s transform pin Note：The above only describes the basic functions that the Target Board will use, for other unlisted parts, please refer to the circuit diagram or contact FAE technical support. ©2022 HYCON Technology Corp APD-HY17MIDE010-V02_EN www.hycontek.com page10...
-
Page 11: Target Board Circuit Diagram
Board.pdf " is placed in the IDE software directory and can be referenced by yourself. * If using Assembly IDE, it’s placed in “HYCON\HY17M IDE\Schematic" directory. * If using H08 C IDE, it’s placed in “HYCON\H08 CIDE\ICESchematic\HY17M" directory. ©2022 HYCON Technology Corp APD-HY17MIDE010-V02_EN www.hycontek.com... - Page 12 Step3: Use the USB Cable to connect to the Control Box’s USB Port and the computer's USB port (the L1 LED will light up). Step4: After Step 1~3 (as shown in Figure 4-5), the hardware connection is completed. Figure 4-5 ©2022 HYCON Technology Corp APD-HY17MIDE010-V02_EN www.hycontek.com page12...
-
Page 13: Revisions
HY17M26 Series IDE Hardware User’s Manual 5. Revisions The following describes the major changes made to the document, excluding the font and punctuation changes. Version Page Date Revision Summary 2022/03/29 First edition ©2022 HYCON Technology Corp APD-HY17MIDE010-V02_EN www.hycontek.com page13...
Need help?
Do you have a question about the HY17M26 Series and is the answer not in the manual?
Questions and answers