Subscribe to Our Youtube Channel
Related Manuals for HYCON HY16F3981
Summary of Contents for HYCON HY16F3981
- Page 1 HY16F3981 IDE Hardware User’s Manual © 2017~2022 HYCON Technology Corp. APD-HY16IDE012-V02_EN www.hycontek.com...
-
Page 2: Table Of Contents
Target Board Features .......................... 9 5.2. External Power Supply and Precautions..................... 10 5.3. Target Board Circuit Diagram ......................11 LCD BOARD INTRODUCTION ......................12 HARDWARE CONNECTION INTRODUCTION ..................13 REVISIONS ............................. 14 © 2017~2022 HYCON Technology Corp APD-HY16IDE012-V02_EN www.hycontek.com page2... - Page 3 HY16F3981 IDE Hardware User’s Manual Attention: 1、 HYCON Technology Corp. reserves the right to change the content of this datasheet without further notice. For most up-to-date information, please constantly visit our website: http://www.hycontek.com 2、 HYCON Technology Corp. is not responsible for problems caused by figures or application circuits narrated herein whose related industrial properties belong to third parties.
-
Page 4: Package Contents
HY16F3981 IDE Hardware User’s Manual 1. Package Contents HY16F3981 IDE Hardware development kit includes HY16F Mini Link and HY16F3981- L064 Target Board. Integrated Hardware development kit helps to develop MCU application program of HY16F3981. Program compiling, hardware debug, IC programming was implemented through NB/PC end connection. -
Page 5: Safety Precautions
When following status occurred, please remove the power supply immediately, and contact our engineer. Power Supply line is worn or damaged. Power source (battery) connected but no any light on while operating. Component off. © 2017~2022 HYCON Technology Corp APD-HY16IDE012-V02_EN www.hycontek.com page5... -
Page 6: Software Installation Requirements
IBM PC compatible X86 system CPU 4GB Memory 8GB Hard disk (2) Product number support: HY16F3981 (3) Hardware model support: HY16F3981 development tools, HY16F3981-DK02. (4) Software version support: AndeSight V2.3.1 RDSp3 version above Device => HY16F_RDSp3_DeviceV0.1 Mini Link Version information => Andes AICE-MINI v1.0.1... -
Page 7: Description Of The Ide Hardware (Hy16F Mini Link)
4. Description of the IDE hardware (HY16F Mini Link) 4.1. Schematic architecture description HY16F Mini Link (AICE) for the HY16F3981-L064 Target Board and PC / NB end, the middle connection device. Mainly used as a Programming program and Debug mode. -
Page 8: Mini Link Connection With Edm
4.4. Connection Diagram of Mini Link and Target Board (Powered by Mini Link) Step1: The EDM Line Connection Mini Link and Target Board. Step2: Connect the PC's USB Port to the Mini Link. Step3: The Power LED is on. STEP1 STEP2 STEP3 © 2017~2022 HYCON Technology Corp APD-HY16IDE012-V02_EN www.hycontek.com page8... -
Page 9: Hardware Target Board Introduction
External power switch see section 5.2 JP8,JP9 External Power (see section 5.2) External power supply voltage regulator circuit Power Management (see section 5.2) Tack Switch*2 S2 and S3 are Tack Switches © 2017~2022 HYCON Technology Corp APD-HY16IDE012-V02_EN www.hycontek.com page9... -
Page 10: External Power Supply And Precautions
Step2: By JP8 (+), JP9 (-) to provide external power supply. (Input range VDD~9.0V) Step3: Press S4 switch (External power switch) Through the Power Management will power regulator into 3V, and then provided to HY16F3981 IC STEP1 STEP3 STEP2 Precautions: Because Mini Link supplied power = 3.3V, so when want to use an external power... -
Page 11: Target Board Circuit Diagram
HY16F3981 IDE Hardware User’s Manual 5.3. Target Board Circuit Diagram © 2017~2022 HYCON Technology Corp APD-HY16IDE012-V02_EN www.hycontek.com page11... -
Page 12: Lcd Board Introduction
HY16F3981 IDE Hardware User’s Manual 6. LCD Board Introduction The LCD panel on HY16F3981-L064 Target Board is HYCON self-owned mold, it’s symbol and pin diagram is shown in below graph. It’s panel specification is as follows: (1) Operating Voltage: 3.0V... -
Page 13: Hardware Connection Introduction
(2.1) In the Target Manager: Local Targets window (2.2) Select HY16F3981 by right-clicking (Select Connect Target via AICE) (2.3) Successful connection appears HY16F3981 AICE: 9902 (2.4) From the Console window, can see the version information of the Mini Link: Andes AICE-MINI v1.0.1... -
Page 14: Revisions
The following describes the major changes made to the document, excluding the punctuation and font changes. Version Page Summary of Changes First Edition 4,8~11 1. Modify the version of HY16F3981 ICE Board. 2. Modify the version of the Target Board circuit diagram © 2017~2022 HYCON Technology Corp APD-HY16IDE012-V02_EN www.hycontek.com...
Need help?
Do you have a question about the HY16F3981 and is the answer not in the manual?
Questions and answers