Download Print this page

NEC MultiSync IDC-3000 User Manual

Improved definition converter.
Hide thumbs

Advertisement

79TM0282
60191
Illinois
Dale,
Wood
Japan
in
Printed
Drive
Michael
1255
Inc.
Technologies,
NEC
IDC-3000
Converter
Definition
Improved
NEC
NEC Improved Definition Converter IDC-3000
R
User's Manual

Advertisement

   Related Manuals for NEC MultiSync IDC-3000

   Summary of Contents for NEC MultiSync IDC-3000

  • Page 1

    79TM0282 60191 Illinois Dale, Wood Japan Printed Drive Michael 1255 Inc. Technologies, IDC-3000 Converter Definition Improved NEC Improved Definition Converter IDC-3000 User's Manual...

  • Page 2

    WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS, UN- LESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE.

  • Page 3: Table Of Contents

    REMOTE CONTROL NOTES ... D ADJUSTMENT ... F The IDC-3000 converts NTSC video signals into scan-doubled signals. This scan converter can be used with a multi-synchronous scan monitor or projectors having a minimum of 31.5 kHz horizontal scanning capability to provide high-quality images.

  • Page 4: Warnings And Safety Precaution

    Si l’appareil est endommagé de cette manière, la garantie devient caduque. De plus, il y a risque d’électrocution. 7. Do not attempt to service or repair the unit. NEC is not liable for any bodily harm or damage caused if unqualified persons attempt service or open the cabinet.

  • Page 5: Part Names And Functions

    Selects image adjustment and audio adjustment. Each time this button is pressed, mode 1 will change as follows: COLOR TINT SHARPNESS 4 DOWN and UP Buttons Used to adjust the item selected with the MODE 1 or MODE 2 button. MONITOR VIDEO NTSC MODE1 DOWN MODE2 VIDEO1...

  • Page 6: Indicators

    A RGB Button Switches the unit to the RGB input mode. H MONITOR Indicator Lights when the MONITOR OUT output is selected at the time of RGB input. I RGB Indicator VIDEO5 Lights when the unit is switched to the RGB input mode with the RGB button.

  • Page 7: Rear Panel

    ON ( ) ... On-screen display will appear on the monitor. OFF ( ) ... On-screen display will not appear on the monitor. 3 TERMINATE Switch (VIDEO 1 and VIDEO 2) Switches the terminating resistor of the BNC input jacks.

  • Page 8

    8 MONITOR Output Jack (OUTPUT) MONITOR (BNC) ... Outputs the signals of the equipment con- nected to VIDEO 1 through 5. S-VIDEO ... Outputs an S video signal, (derived from the signal of the equipment connected to VIDEO 1 or VIDEO 2), which has been divided to a luminance signal (Y) and a chrominance signal (C).

  • Page 9: Remote Control

    7 RGB Button Switches the unit to the RGB input mode. 8 MONITOR Button Used to switch on the monitor mode at the time of RGB input. 9 SPLIT Press to activate the demonstration split mode function for processing the artificial interlace and switching off the 3-dimensional Y/C separa- tion processing the right half of the screen.

  • Page 10: Remote Control Notes

    REMOTE CONTROL NOTES Remote Control Precautions The remote control system may not function when direct sunlight or strong illumination strikes the remote sensor window of the main unit. Do not place in locations where there is a high temperature or high humidity.

  • Page 11: Adjustment

    ADJUSTMENT Adjustment of COLOR, TINT, SHARPNESS, and SOUND (1) Press the MODE 1 button and select the mode to be adjusted. Each press of the MODE 1 button will change the selection as follows: COLOR TINT SHARPNESS (2) While the indicator is on, press and hold the UP or DOWN button and adjust.

  • Page 12: On-screen Display

    ON-SCREEN DISPLAY Screen Display During Input Signal Selection SOURCE VIDEO 1 Display characters during video 1 to 5 input signal selection During video 1 input signal selection ... SOURCE During video 1 S input signal selection ... SOURCE During video 2 input signal selection ... SOURCE During video 2 S input signal selection ...

  • Page 13

    Screen Display During Split Mode Selection SPLIT ON Display characters during split mode selection in mode 2 During split selection ... SPLIT ON When split is not selected ... SPLIT OFF Display color SPLIT ON ... Cyan SPLIT OFF ... Cyan Screen Display During NORMALIZED Selection NORMALIZED A press of the “NORMALIZED”...

  • Page 14

    During the TINT (Center) Adjustment TINT Display characters during the tint adjustment Display color during the center adjustment Tint ... Green R ... Red G ... Green ... Red ... Green During the TINT (G Direction) Adjustment TINT Display characters during the tint adjustment Display color during the adjustment in the G direction Tint ...

  • Page 15

    During the SOUND Adjustment SOUND – Display characters during the sound adjustment Display color SOUND ... Green Normal ... Magenta Max ... Red Min ... Blue During the SPLIT Screen Selection SPLIT ON Display characters during the split mode selection During split selection ...

  • Page 16: Hook-up Examples

    RGB (THROUGH) MONITOR VIDEO1•2 S ONLY AUDIO AUDIO AUDIO AUDIO AUDIO OUTPUT Video input of an NEC MultiSync monitor or an S-VIDEO input of a monitor. HORIZONTAL HV-POL. PC-CONTROL VERTICAL PC-CONTROL EXTERNAL CONTROL RGB inputs of projectors or moni- tors such as NEC MultiSync pro-...

  • Page 17: Using The External Control Connector

    Using the EXTERNAL CONTROL Connector 10 9 15 14 13 12 11 Mini D-SUB 15 Pin Pin No. Function Input switching Power on/off Input switching Input switching External control on/off Ground NOTE: Button operations of the main unit and the remote control are not possible during use of external control.

  • Page 18

    Connection Examples for Personal Computer Control for the Two Varia- tions. 1 RS-232C PC-CONTROL Terminal IDC-3000 2 RS-422 PC-CONTROL Terminal IDC-3000 2 When using the PC-CONTROL terminal as RS-422: Request to Send - Request to Send + Transmit Data + Receive Data + 10 9 15 14 13 12 11...

  • Page 19: Rack Mounting

    RACK MOUNTING Use the accompanying rack mount bracket to mount the IDC-3000 to the rack. NOTE: This rack mount bracket is designed for used with EIA standard racks. Remove the four (A) screws from the IDC-3000. Mount the IDC-3000 to the rack and tighten the screws. 482.6mm 465.1mm 108.0mm...

  • Page 20: Specifications

    SPECIFICATIONS Jacks VIDEO 1 through 5 BNC input S input Audio input L and R channels MONITOR OUT BNC output S output Audio output L and R channels RGB Input BNC Input Audio input L and R channels RGB Output...

  • Page 21: Appendix

    APPENDIX (IDC-3000 stand alone PC-CONTROL command reference) You can control the main functions from external equipment such as personal computer using the PC-CONTROL terminal. The following sections explain the interface. Interface Condition • RS-232C or RS-422 • Baud rate ... 9600 bps •...

  • Page 22

    PC CONTROL COMMAND LIST FOR USE WITH THE IDC-3000 IDC-3000 COM2 Contents COM1 Power On Power Off Input switching Example: Input switching (VIDEO 1) from the PC to the IDC-3000 (when the address selector equals 0) IDC-3000 COM1 UA COM2 Leng Data Sum VIDEO 2 : 02 VIDEO 3 : 03 VIDEO 4 : 04...

  • Page 23: Limited Warranty

    PROFESSIONAL GRAPHICS PRODUCTS LIMITED WARRANTY NEC Technologies, Inc. (hereafter NECTECH) warrants this product to be free from defects in material and workmanship under the following terms. HOW LONG IS THE WARRANTY Parts and labor are warranted for (1) One Year from the date of the first customer purchase.

  • Page 24

    • MEMO •...

Comments to this Manuals

Symbols: 0
Latest comments: