Advertisement
to the next step: confirm 'Domain create?'
with 'Y'.
It takes about 5s to create a new appartment
address. The module is then configured (LED is
off). The display moves to the next step: issue
the group address g and device address e.
2. Assign address
Set the address g by pressing buttons ▲ and
■
▼ in section A, .... , O. Press 'Y' to confirm
and save or press 'N' to reject and move to
the next step: assign address e.
■
Set the address e using buttons s and t in
section 0, .... , 127. Press 'Y' to confirm and
save or press 'N' to reject. Address e = 0 is
a group address and a temperature controller
with g, e = 0 switches all actuators with the
same g, irrespective of the actuator e.
The menu moves to the next step: set heating
or cooling.
3. Heating (On/off or PWM) and cooling
modes
Press buttons ▲ and ▼ to switch between
■
heating and cooling mode. Press 'Y' to con-
firm and save or press 'N' to reject and move
to the next step: set an offset temperature
value.
In heating mode, output 4 switches on when
the temperature actual value is below the
setpoint. Output 5 is switched off.
In PWM mode, it is switched on and off per-
centage-wise within a 30-minute interval by
means of a PID control. This is particularly
suitable for underfloor heating.
In cooling mode, output 5 switches on when
the temperature actual value is above the
setpoint. Output 4 is switched off.
4. Set temperature offset
If a temperature controller systematically
indicates a temperature reading that is con-
stantly too high or too low, this can be com-
pensated by a temperature offset. Set the
offset using buttons ▲ and ▼ to correct the
displayed temperature. Press 'Y' to confirm
and save or press 'N' to reject. The program
then exits the configuration menu and reverts
to normal mode (see step 6).
5. Configuration menu from normal mode
To return to the configuration menu with
configured modules:
a Hold down the two left buttons on the display
(absent and present) for at least 5 seconds
until mode 'Heat/Cool' appears. Then set
the heat/cool mode and the temperature
offset. The menu continues with Step 3.
b Hold down the 2 left keys of the display
(absent and present) for at least 10 seconds,
until the *language (Deutsch/English)
appears.
■
Select the language with the buttons s
and t and confirm with 'Y', the menu
goes on to the next step: RESET? The
appartment address of the temperature
controller will be deleted with RESET
and the delivery state will be restored.
■
Perform a RESET with 'Y', the module is
now unconfigured.
■
Or reject with 'N', the menu goes on to
the next step:
'Domain extend?'
The appartment address of the temperature
controller is assigned to non-configured
modules by 'Domain extend'. Thereby
new powerline modules can be inte grated
into the apartment.
■
Confirm with 'Y' or reject with 'N', the
menu continues with step 2.
6. Normal mode
The temperature controller indicates the
actual room temperature. The heating and
cooling modes are indicated by the symbols
and .
Press the buttons ▲ and ▼ to modify the
■
setpoint. The setpoint is displayed and
goes out after 5 seconds if no further
changes are made.
■
Two preset setpoints can be saved. To
save, set the setpoint required and press
one of the buttons 'absent' or 'present'
while the setpoint is still displayed. This
saves the setpoint for this button and it
can be recalled at the press of a button in
normal mode.
After a power failure, the setpoint is set to
the value saved at 'absent'.
In the as-delivered state the following tem-
perature values are saved:
- Absent: 15°C
- Present: 20°C
Send node ID:
Use a small insulated screwdriver to briefly
press Service PIN. The Powerline node ID is
sent.
Must be kept for later use!
Eltako GmbH
D-70736 Fellbach
Technical Support English:
+49 711 94350025
technical-support@eltako.de
eltako.com
51/2020 Subject to change without notice.
Advertisement
