Quick Start MobileView Guard G750 Catalog Numbers (2727-G7P20D1P4, 2727-G7P20D1P5, 2727-G7P20D1Q6, 2727-G7P20D3Q7) English For more detailed information on the MobileView Guard G750, refer to publication 2727-UM002. Download a free electronic version of publication 2727-UM002 from: • installation CD • www.support.rockwellautomation.com www.theautomationbookstore.com Inside .
MobileView Guard G750 Important User Information Because of the variety of uses for the products described in this publication, those responsible for the application and use of this control equipment must satisfy themselves that all necessary steps have been taken to assure that each application and use meets all performance and safety requirements, including any applicable laws, regulations, codes and standards.
MobileView Guard G750 Safety Precautions and Elements This section covers general safety precautions in addition to important information on the power supply, emergency stop switch, and enabling switches used with the MobileView Guard G750. General Safety It is important to follow the instructions in this document in all circumstances.
Page 7
MobileView Guard G750 Handling of MobileView Guard Terminal Refer to MobileView Guard G750 User Manual for additional handling instructions to avoid terminal malfunctions or damage. Power Supply • The device meets safety class III in accordance with EN ATTENTION 61131-2 and EN 50178. The 24V power supply for the...
Page 8
MobileView Guard G750 • In special operating mode, safety must be guaranteed in other ways since the operator must enter dangerous areas of the machine, and targeted movements must be possible. In this case, a reduced speed of the machine must be defined by means of the risk assessment.
Page 9
MobileView Guard G750 Connection Example with a Safety Control Relay The diagram below shows suggested wiring for enabling switches using an PILZ PST safety control relay to meet safety category 3. Refer to PILZ PST documentation for additional information. MobileView...
Page 10
MobileView Guard G750 Switching Element Data Nominal voltage 24V dc (typical) 32V dc (maximum) Nominal current 500 mA (typical) Short-circuit current circuit 1; maximum 1.9 A circuit 2: maximum 600 mA Max. inductive load (at 500 mA) circuit 1: >1H circuit 2: maximum 320 mH Max.
Page 11
MobileView Guard G750 Emergency Stop Switch The emergency stop switch of the MobileView terminal meets the requirements of EN 418. It must be designed as an emergency stop of category 0 or category 1 (see EN 60204-1, chapter 9.2.5.4.2) on the basis of the risk assessment for the machine.
MobileView Guard G750 MobileView Junction Box Mounting and Wiring The MobileView Junction Box (2727-MRJB1) integrates the MobileView terminal into the control system and is mounted on a DIN rail. RJ-45 jack for connecting the MobileView data lines. 9-pin DSUB female connector (for future use).
Page 13
MobileView Guard G750 Mounting Junction Box on a DIN Rail Mount the MobileView Junction Box within an enclosure using a DIN rail. To install the Junction Box on a DIN rail: 1. Mount the DIN rail. 2. Hook the top slot over the DIN rail.
Page 14
MobileView Guard G750 Connecting the MobileView to the Junction Box The following illustration shows how the MobileView terminal connects to the Junction Box. Junction Box Typical Control Cabinet MobileView Terminal 24V D C Pin 1, 24V dc ON LY +24V...
Page 16
MobileView Guard G750 Power Supply Requirements Electrical Specifications 24V dc Power Supply Use a 24V dc Safety Extra Low Voltage power supply. Supply Voltage Range: 18V dc to 32V dc Current Consumption: 300mA at 24V dc Peak Inrush Current: 5.6 A maximum...
Page 17
MobileView Guard G750 MobileView Connection Cable The MobileView Connection Cable (2727-MRTxx) connects the MobileView terminal to the Junction Box Cable. The Connection Cable is 5, 10, 15, or 20 meters (16.4, 32.8, 49.2, or 65.6 feet). This cable withstands water, cleaning agents, motor oil, drilling oils, grease, lubricants and condensates containing hydrochloric acid.
Page 18
MobileView Guard G750 MobileView Junction Box Cable The MobileView Junction Box Cable (2727-MREX1) connects the Junction Box to the circular jack in the wall of the enclosure. The cable length is 2 meters (6.5 feet). When the MobileView terminal is not connected to the Junction box, the dust cover provides protection for the 17-pin connector.
MobileView Guard G750 MobileView Terminal This section provides details on: • How to remove the back cover of the MobileView terminal • Ethernet connection • Using the PC Card slot Removing the Back Cover This section shows how to remove the back cover of the MobileView terminal.
Page 20
MobileView Guard G750 The following illustration shows what the connection area of the MobileView terminal looks like with the back cover removed. Reset Button RS-232 Port Ethernet Label for rebooting Windows CE. for downloading software. Ethernet (Mac) Address All data not flushed to Registry or Main connector (S19) saved to Flash Storage is lost.